Skip to content
Independent home-inspection guidance. We are not affiliated with the prior occupant of this domain.
Find an inspector

Furnace Replacement Cost: Gas, Electric and Heat Pump Options

By InspectandTest Editorial Team Published October 3, 2026 Updated November 12, 2026

We may earn commission from links on this page. Lead-form submissions are forwarded to local inspector partners. How we research and review.

Photo via Unsplash by Peter Fly

A furnace rarely gives much warning before it becomes a problem. It might fail on the first cold night of October, or an HVAC technician might flag a cracked heat exchanger during a routine tune-up, and suddenly a homeowner is comparing quotes under pressure. Understanding the typical furnace replacement cost before that moment makes it far easier to judge whether a bid is reasonable, whether a higher-efficiency model is worth it, and whether a heat pump or dual-fuel system deserves a look. This guide walks through rough price ranges for gas, electric and oil furnaces and for heat pumps, explains what pushes quotes up, covers Front Range issues such as altitude derating, and outlines when replacement makes more sense than another repair. All figures are general 2026 estimates that vary widely by home, equipment brand, ductwork condition and contractor, so treat them as a starting point rather than a firm price.

Heating or cooling trouble? Talk to a local HVAC technician.

📞 Call (833) 491-1876

Free, no-obligation quote · Connect with a local pro. Calls may connect you with a partner contractor; we may be compensated for calls.

How Much Does a Furnace Replacement Cost?

For a straightforward like-for-like swap of a standard gas furnace in a typical single-family home, many homeowners see installed quotes somewhere in the range of roughly $3,500 to $7,500. High-efficiency condensing furnaces, larger homes, difficult attic or crawl space installations and ductwork changes can push that figure to $8,000, $10,000 or more. Electric furnaces usually cost less to install but more to operate in most markets, while heat pumps and dual-fuel systems often cost the most up front.

A replacement quote normally bundles several items: the furnace itself, labor, removal and disposal of the old unit, new venting or venting modifications, a new filter rack or return connections, thermostat wiring, gas line and electrical connections, the permit and the startup and combustion check. If the air conditioner coil sits on top of the furnace, it may need to be reset or replaced, which adds cost. A good written estimate itemizes these pieces so homeowners can compare bids line by line rather than by bottom line alone.

The sections below summarize commonly quoted ranges by system type. They are not price guarantees, and prices along the Front Range can run above national averages during peak heating season.

Furnace Replacement Cost by System Type

Standard-Efficiency Gas Furnace (80% AFUE)

An 80 percent AFUE (Annual Fuel Utilization Efficiency) gas furnace is the traditional mid-efficiency option. Installed prices often fall around $3,000 to $6,000. These units vent hot exhaust through a metal flue, usually shared with a gas water heater and run up through the roof or into a chimney. Because they can reuse an existing flue, replacements are often simpler and cheaper. The trade-off is that about a fifth of the fuel energy is lost up the vent. Current federal efficiency rules and local codes affect which non-condensing models can still be installed in a given region, so ask the contractor what is permitted in the specific jurisdiction.

High-Efficiency Condensing Gas Furnace (90%+ AFUE)

Condensing furnaces rated at roughly 90 to 98 percent AFUE extract so much heat from the exhaust that water vapor condenses inside the unit. Installed prices commonly run around $4,500 to $9,000 or more. The venting is completely different: these furnaces typically use PVC or similar plastic pipe, often with a separate combustion-air intake, routed through a sidewall or the roof. They also need a condensate drain, and sometimes a condensate pump, plus freeze protection where drain lines run through cold spaces.

Switching from an 80 percent unit to a condensing model can trigger extra work. If the old furnace shared a metal flue with a gas water heater, removing the furnace from that flue can leave the water heater “orphaned” in a chimney or vent that is now oversized for it alone. Many contractors will recommend a chimney liner or vent change for the water heater in that situation, so ask whether it is included. According to ENERGY STAR’s furnace page, certified gas furnaces for the northern half of the U.S. carry the standard label and are described as up to 18 percent more energy efficient than baseline models.

Electric Furnace

Electric resistance furnaces are mechanically simple, with no combustion, no flue and no gas line. Installed costs often range from about $2,000 to $5,500. The catch is operating cost. Electric resistance heat converts electricity to heat at close to a one-to-one ratio, which tends to be expensive in a cold climate compared with natural gas or a heat pump. A large electric furnace may also require a dedicated high-amperage circuit, and in some older homes that can mean an electrical panel upgrade before installation.

Oil Furnace

Oil heat is uncommon along the Front Range but still shows up in some older or rural properties. Replacement oil furnaces commonly run around $4,000 to $9,000 installed, with added cost if the oil tank is old, leaking or needs removal. Many owners in this situation price out a switch to natural gas or propane, or to a heat pump, since fuel delivery and tank maintenance are ongoing expenses.

Heat Pumps and Dual-Fuel Systems

A ducted air-source heat pump that replaces both the furnace and air conditioner often costs roughly $7,000 to $16,000 or more installed, depending on capacity, efficiency and whether the system is rated for cold climates. A dual-fuel setup pairs a heat pump with a gas furnace that takes over in the coldest weather; these commonly land between about $8,000 and $18,000. Ductless mini-split systems are another option for homes without ductwork or for additions.

ENERGY STAR’s air-source heat pump page notes that many newer certified heat pumps provide space heating even in very cold climates, that cold-climate certification involves verified testing down to 5°F, and that pairing a cold-climate heat pump with a back-up energy source is the most efficient approach when temperatures fall even lower. Front Range winters bring regular cold snaps and occasional subzero nights, so many local contractors propose either a cold-climate heat pump with electric backup or a dual-fuel system. Whether a heat pump makes financial sense depends heavily on local gas and electricity rates, the home’s insulation and air sealing, and the specific equipment, so get a load calculation and an operating-cost comparison rather than relying on a general rule.

What Drives the Price of a New Furnace

Sizing and the Load Calculation

Bigger is not better. An oversized furnace short-cycles, runs louder, wears faster and can leave rooms uneven. ENERGY STAR’s quality installation guidance asks homeowners to make sure the contractor sizes equipment using the actual characteristics of the home rather than a rule of thumb, and its ductless heating and cooling page names “Manual J” as the calculation contractors should use to verify system size. A contractor who simply matches the old furnace’s capacity may be repeating an earlier sizing mistake, particularly if the home has since been insulated, re-windowed or air sealed. Results from a home energy audit can feed directly into a better load calculation.

Ductwork Condition

Leaky, undersized or poorly balanced ductwork can undermine even an excellent furnace. Some quotes include sealing accessible duct joints, adding a return, or replacing a damaged plenum. Full duct replacement is a separate, often substantial cost. Asking the contractor to measure static pressure and airflow before and after installation is a reasonable request on a higher-end job.

Venting and Gas Supply

Venting changes are one of the biggest variables. Moving to a condensing furnace means new plastic venting and a condensate drain. Keeping an 80 percent unit means verifying the existing flue is sound and correctly sized. Some upgrades also require a larger gas line, a new shutoff valve or a sediment trap to meet current code.

Altitude Derating on the Front Range

At Denver’s elevation of roughly 5,280 feet, and higher in foothills communities in Jefferson, Boulder and Douglas counties, the air contains less oxygen. Gas furnaces must be set up for altitude according to the manufacturer’s instructions, which can include orifice changes, pressure switch changes or derated input. Derating is often expressed as a percentage reduction in input per 1,000 feet above a threshold elevation, though the exact requirement varies by model. The practical result is that a furnace’s nameplate capacity at sea level may not match what it delivers here, and sizing should account for that. Ask contractors whether the quote includes high-altitude conversion parts and whether the unit is approved for the home’s elevation.

Permits, Access and Timing

Most Front Range jurisdictions require a mechanical permit for furnace replacement, and the permit inspection checks venting, gas connections, combustion air and clearances. Permit fees are usually a small part of the total, but skipping the permit can complicate a later sale. Tight attics, crawl space installs and furnaces in finished basements add labor. Emergency replacements in January also tend to cost more than planned replacements in late summer.

Equipment Features

Single-stage, two-stage and modulating gas valves, along with variable-speed blower motors, change both the price and the comfort. Two-stage and modulating units run longer at lower output, which tends to even out temperatures and reduce noise. Warranty length and whether the contractor registers the equipment also differ between brands and installers.

When Replacement Beats Another Repair

Not every failed furnace needs to be replaced. Igniters, flame sensors, inducer motors, pressure switches and control boards are common repairs that can keep a mid-life furnace running for years. The decision usually comes down to age, safety, repair frequency and efficiency.

  • Age: ENERGY STAR’s guidance on when to replace heating equipment suggests considering replacement when a furnace or boiler is more than 15 years old.
  • Repair frequency and rising bills: The same ENERGY STAR page lists frequent repairs combined with rising energy bills as another sign that replacement may be due.
  • Comfort problems: Rooms that are consistently too hot or too cold can point to equipment, duct or insulation problems; a proper evaluation separates these.
  • Safety findings: A cracked or breached heat exchanger is the classic reason a technician recommends replacement over repair.

Heat exchangers separate combustion gases from the air circulated through the home. When one cracks, combustion byproducts, including carbon monoxide, may have a path into the airstream. Replacing a heat exchanger alone is sometimes possible under warranty, but on an older furnace the labor cost often makes full replacement the better value. The guide on a cracked heat exchanger covers the signs, the testing methods technicians use and how to respond to a red-tag notice.

A rough rule many homeowners use is to weigh the repair cost against the furnace’s remaining life. A $600 repair on a five-year-old furnace is usually easy to justify. The same repair on an 18-year-old unit that has needed three service calls in two winters is a different calculation. Getting a second opinion on any recommendation to replace, especially one based on a reported heat exchanger crack, is reasonable and common.

Rebates, Tax Credits and Efficiency Payback

Incentives change often, so verify every program before counting on it. ENERGY STAR’s federal tax credit page describes energy efficiency home improvement credits, including for furnaces and air-source heat pumps, as available through December 31, 2025. Some older ENERGY STAR product pages still show longer timelines, so check current IRS guidance for any purchase made in 2026 rather than relying on a single page. Utility programs and state or local incentives may also apply; ENERGY STAR’s rebate finder lists partner-sponsored rebates by ZIP code, and Front Range utilities periodically offer rebates on high-efficiency furnaces, heat pumps and smart thermostats.

Payback from a higher-efficiency furnace depends on gas prices, how many heating hours the home needs and how leaky the house is. In a cold climate with long heating seasons, the gap between 80 and 95 percent AFUE can add up over a furnace’s life. In a small, well-insulated home with low gas use, the savings may take much longer to recover the higher installed cost. Air sealing and insulation upgrades often deliver savings no matter which furnace is chosen.

Carbon Monoxide Safety During and After Replacement

Any fuel-burning furnace is a potential carbon monoxide source if venting, combustion or the heat exchanger fails. The U.S. Consumer Product Safety Commission recommends battery-operated CO alarms, or alarms with battery backup, on every level of the home and outside sleeping areas, and notes that interconnected alarms are best. A furnace replacement is a natural time to check that the home has working alarms in the right places. Combination and standalone units are listed in the CO and gas detector category.

After installation, a qualified technician should perform a combustion analysis and verify draft and venting. If the old flue still serves a water heater, confirm that it was evaluated. Snow drifts and ice can block sidewall vents on condensing furnaces during Colorado storms, so homeowners should know where the intake and exhaust terminate and keep them clear.

How to Get a Fair Furnace Quote

  1. Get at least three written, itemized bids. ENERGY STAR’s contractor tips recommend comparing cost, efficiency and warranties, and signing a written proposal that lists model numbers, costs and schedule.
  2. Ask for a load calculation. A contractor who measures the house and runs Manual J is more likely to size correctly than one who matches the old nameplate.
  3. Clarify venting and water heater work. Make sure each bid states what happens to the existing flue and the water heater’s vent.
  4. Confirm altitude setup. The quote should mention high-altitude conversion or derating where the manufacturer requires it.
  5. Check permit, startup and warranty details. Ask who pulls the permit, whether combustion testing is included and how labor warranties work.
  6. Compare system types honestly. If one contractor proposes a heat pump or dual-fuel system, ask for an operating-cost comparison based on local utility rates.

Buyers face a slightly different version of this decision. A general home inspection evaluates the visible, accessible parts of the heating system but is not a full HVAC teardown. When a furnace is older or shows warning signs, a dedicated furnace inspection by a qualified technician can give a clearer picture of remaining life and safety before closing. The HVAC inspector guide explains how that evaluation differs from a standard inspection, and the broader guide to hiring a home inspector covers how to fit specialist evaluations into a purchase timeline. An expected furnace replacement cost can also become a reasonable point in negotiations when the evidence supports it.

More Questions About Furnace Replacement Cost

How long does a furnace replacement take?

A straightforward furnace replacement typically takes one day, often about four to ten hours, when the new furnace fits the existing ductwork, venting and gas line. The crew removes the old unit, sets the new one, connects everything and tests it.

Jobs can stretch to two or three days when they involve converting to a high-efficiency furnace with new PVC venting, modifying ductwork, relocating equipment or replacing the air conditioner at the same time. Permit inspections may also add a follow-up visit.

Is it cheaper to replace the furnace and air conditioner together?

Replacing the furnace and air conditioner together is often cheaper overall than doing them separately, because the crew handles both in one visit and some installers offer package pricing. Matched systems can also work more efficiently, since the blower is paired with the new coil.

It makes the most sense when the air conditioner is also near the end of its life, often 12 to 15 years old or more. A newer, healthy air conditioner usually does not need replacing just because the furnace failed.

Does a new furnace increase home value?

A new furnace rarely adds its full cost to a home’s appraised value, but it can make a house easier to sell. Buyers and home inspectors pay attention to the age of major systems, and an old furnace often becomes a negotiating point or repair request.

A recent replacement with transferable warranty paperwork and permit records can reassure buyers. Homeowners planning to sell soon should weigh the furnace’s condition and age rather than replacing a working unit solely for resale.

Can furnace replacement be financed?

Yes, furnace replacement can often be financed through HVAC contractors, manufacturers, utilities or personal loans. Many contractors offer promotional plans, sometimes with deferred interest, while some utilities and state programs offer low-interest loans for high-efficiency equipment.

Compare the full cost of each option, including interest rates after any promotional period ends and fees. Deferred-interest offers can charge back interest if the balance is not paid in time. Rebates and tax credits may reduce the amount that needs financing.

What is the best time of year to replace a furnace?

Spring and early fall are generally the best times to replace a furnace. Demand is lower, installers have more flexible schedules, and homeowners can compare quotes without the pressure of a home with no heat.

Planning ahead also allows time to check rebates, choose efficiency levels and arrange permits. Replacing an aging furnace before it fails, rather than during a winter emergency, avoids rushed decisions and the possibility of waiting days for equipment during peak season.

References

Frequently asked questions

How much does it cost to replace a furnace?

As a rough 2026 range, a like-for-like gas furnace replacement often costs about $3,500 to $7,500 installed. High-efficiency condensing models, ductwork changes, difficult access and venting work can push quotes well past $8,000, while heat pumps and dual-fuel systems usually cost more.

Is a 95 percent furnace worth it over an 80 percent furnace?

In cold climates with long heating seasons, a condensing furnace often recovers its higher price through lower gas bills over time. The answer depends on gas rates, home size, insulation and how much venting work the switch requires, so ask contractors for an operating-cost comparison.

How long do furnaces last?

Many gas furnaces last somewhere around 15 to 20 years with regular maintenance. ENERGY STAR suggests considering replacement when a furnace is more than 15 years old, especially if repairs are frequent and energy bills are rising.

Do furnaces need to be adjusted for altitude in Colorado?

Yes. Gas furnaces installed at Front Range elevations must be set up according to the manufacturer's high-altitude instructions, which may involve orifice or pressure switch changes and derated input. Ask the installer to confirm the unit is approved and configured for the home's elevation.

Should I replace my furnace if the heat exchanger is cracked?

A cracked heat exchanger can allow combustion gases into the home's air, so technicians often shut the furnace off and recommend replacement. On a newer furnace, a warrantied heat exchanger replacement may be an option. Getting a second opinion with photos or camera evidence is reasonable.

Does homeowners insurance pay for furnace replacement?

Homeowners insurance usually pays for furnace replacement only when the damage comes from a covered peril such as fire, lightning or certain flooding events. Furnaces that fail from age or wear are typically excluded. An equipment breakdown endorsement may cover some mechanical failures.

Should ductwork be replaced along with the furnace?

Ductwork does not always need replacing with a new furnace. A contractor should check for leaks, damage, poor sizing and disconnected sections. Sealing and modifying existing ducts is often enough, while badly undersized or deteriorated ducts may justify replacement during the project.

Is removal of the old furnace included in replacement quotes?

Removal and disposal of the old furnace is usually included in replacement quotes, but it is worth confirming in writing. Oil furnace replacements may involve separate charges for oil tank removal or abandonment, which can add significant cost and sometimes require permits.

Buying a Front Range home with an aging furnace or a fresh red tag on the heating system? Get in touch with us and we can help connect you with a local inspector who can look at the system before you commit.