Home Energy Audit: What It Finds, Blower Door Tests and Cost
High heating bills, drafty bedrooms, and an upstairs that never cools down in July are all symptoms of the same underlying question: where is the house actually losing energy? A home energy audit answers that with measurements instead of guesses. A professional auditor pressurizes or depressurizes the house to measure air leakage, scans walls and ceilings with an infrared camera, checks ductwork, and tests gas appliances for safe operation. This guide explains what a home energy audit includes, how a do-it-yourself walkthrough compares with a professional test, how to read the report, what audits typically cost, where rebates may come from, and how an audit differs from the home inspection a buyer orders before closing. Cost figures here are broad industry ranges, and incentive programs change frequently, so confirm details with local providers and your utility.
Part of our Crawl Space & Attic Guide guide — start there for the full picture →
What Is a Home Energy Audit and What Does It Find?
A home energy audit, sometimes called a home energy assessment, is a whole-house evaluation of how energy is used and lost. ENERGY STAR describes a professional audit as a way to find hidden air leaks, pinpoint specific solutions for a home, and identify potential safety issues. In practice, a professional audit usually finds some combination of the following:
- Air leaks at the attic floor, rim joists, plumbing and wiring penetrations, fireplaces, and around windows and doors
- Missing, thin, or settled insulation in attics, walls, and floors over unconditioned spaces
- Leaky or disconnected ductwork, particularly in attics, crawl spaces, and garages
- Combustion appliances that backdraft or produce elevated carbon monoxide
- Aging or oversized heating and cooling equipment
- Moisture problems such as attic frost, damp crawl spaces, or bath fans that vent into the attic
The deliverable is typically a written report ranking improvements by cost-effectiveness, so homeowners can spend money on the fixes that matter most rather than defaulting to new windows, which are often one of the least cost-effective upgrades per dollar.
What a Professional Audit Includes
Auditors vary in thoroughness, but a full diagnostic audit usually follows a predictable sequence. Expect two to four hours on site for a typical single-family home.
Interview and Utility Bill Review
Most auditors start by asking about comfort complaints, the age of major equipment, and past upgrades. Twelve months of utility bills help establish a baseline and reveal whether usage is unusually high for the home’s size and age.
Blower Door Test
The blower door is the centerpiece of a diagnostic audit. A calibrated fan is mounted in an exterior doorway with an airtight frame and panel. The auditor closes exterior windows and doors, opens interior doors, and runs the fan to depressurize the house, commonly to 50 pascals below outdoor pressure. A gauge measures how much air the fan must move to hold that pressure. The result is reported as CFM50 (cubic feet per minute at 50 pascals) and often converted to ACH50, the number of times the house’s air volume would be exchanged per hour at that pressure.
While the house is under pressure, leaks become much easier to find. The auditor may walk the house with a smoke pencil or infrared camera, and homeowners can often feel drafts at outlets, baseboards and attic hatches that were never noticeable before.
Infrared Scan
Thermal imaging shows surface temperature differences that point to missing insulation, air leakage paths, and sometimes moisture. Scans work best when there is a meaningful temperature difference between indoors and outdoors, which is why fall and winter mornings on the Front Range are good times to schedule. The site’s overview of thermal imaging in home inspections explains what infrared cameras can and cannot reveal.
Combustion Safety Testing
Any home with a gas furnace, boiler, water heater, fireplace, or range should get combustion safety testing as part of an audit. The auditor checks for gas leaks, measures carbon monoxide in flue gases and ambient air, and runs a worst-case depressurization test with exhaust fans and the dryer running to see whether naturally drafting appliances can still vent properly. This matters because air sealing makes a house tighter, and a tighter house can change how atmospherically vented appliances draft. The EPA notes that combustion pollutants such as carbon monoxide and nitrogen dioxide are a known indoor air quality concern, so this part of the audit is a safety step, not an upsell.
Duct Leakage Testing
Ducts that run through attics, crawl spaces, or garages can leak a meaningful share of conditioned air into unconditioned space. ENERGY STAR estimates that in a typical house about 20 to 30 percent of the air moving through the duct system is lost to leaks, holes and poorly connected ducts. Some auditors measure duct leakage directly with a duct blaster, a smaller calibrated fan connected to the system, while others estimate it from a visual inspection and pressure readings. Duct leakage testing is especially worthwhile when the furnace or air handler sits in the attic.
Visual Inspection of the Envelope and Systems
The auditor will usually inspect the attic, crawl space or basement, water heater, furnace or boiler, windows, lighting, and major appliances. Insulation depth and coverage are noted, along with moisture, ventilation problems, and suspect materials such as vermiculite that should be tested before anyone disturbs it.
DIY Energy Audit vs Professional Audit
A homeowner walkthrough is free and can catch obvious problems. ENERGY STAR publishes DIY checks that include looking for gaps around pipes and wires, checking attic insulation depth, inspecting weatherstripping, and looking for dirty spots on insulation that indicate air movement. A DIY approach is reasonable for:
- Measuring attic insulation depth with a ruler
- Checking the attic hatch and door weatherstripping
- Holding a lit incense stick near outlets, windows and baseboards on a windy day to spot drafts
- Looking for disconnected or crushed ducts in accessible spaces
- Reviewing utility bills for unusual spikes
What a DIY walkthrough cannot do is quantify the problem. Without a blower door, there is no baseline number to compare against after air sealing, and without combustion testing, there is no way to confirm that tightening the house is safe for gas appliances. A professional audit also identifies hidden bypasses, such as open chases behind soffits, that are difficult to find without pressure testing.
Many homeowners use both: a DIY pass to fix the easy items, then a professional audit when planning larger work such as attic insulation, duct sealing, or equipment replacement.
How Much Does a Home Energy Audit Cost?
Industry estimates suggest a full professional audit with blower door, infrared scanning and combustion testing commonly runs somewhere in the range of roughly $200 to $700 for a typical single-family home, with larger or more complex homes costing more. Visual-only walkthroughs are often cheaper. Some utilities and local programs offer free or reduced-cost audits, sometimes with direct-install measures such as LED bulbs, low-flow showerheads, or basic weatherstripping included.
Several factors influence price:
- Home size, number of stories, and number of HVAC systems
- Whether duct leakage is measured with a duct blaster or estimated
- Whether the audit is bundled with a contractor’s sales visit or performed by an independent auditor
- Travel distance, especially for foothill and rural properties outside the Denver metro
- Whether a “test-out” visit after improvements is included
Independent auditors who do not sell the recommended work avoid an obvious conflict of interest. Contractor-provided audits can still be useful, but compare their recommendations against at least one other opinion before committing to a large project.
Rebates, Utility Programs and Incentives
Incentives for audits and efficiency upgrades come from several places, and the details change often. Common sources include:
- Electric and gas utilities. Many utilities run audit programs and offer rebates for insulation, air sealing, smart thermostats, and high-efficiency equipment. Check your utility’s website or call its efficiency line for current offers.
- State and local programs. Some states, counties, and cities offer additional incentives or financing for qualifying improvements.
- Federal tax provisions. Federal tax credits for efficiency improvements have changed over time; confirm current rules with a tax professional before counting on them.
The ENERGY STAR rebate finder lets homeowners search by ZIP code for programs tied to certified products. Many programs require a participating auditor or contractor, pre-approval before work starts, or specific documentation, so read the requirements before scheduling anything.
How to Read Your Energy Audit Results
A good report should be readable without a physics degree. The key numbers and sections to look for:
Air Leakage (CFM50 and ACH50)
Lower is tighter. Older homes can test far leakier than modern energy codes require for new construction, which commonly set limits in the range of 3 to 5 ACH50 depending on the code edition and climate zone. A high number on an older house simply indicates room to improve. Ask the auditor what reduction is realistic after targeted air sealing.
Insulation Levels
The report should state existing attic, wall and floor insulation levels and compare them with recommended targets. For most of the Front Range, which falls in climate zone 5, ENERGY STAR recommends attic levels in the R-49 to R-60 range. The site’s guide to attic insulation types and R-values covers that work in more detail.
Combustion Safety Results
Look for pass or fail results on draft, spillage and carbon monoxide for each appliance. Any failure should be addressed before air sealing begins, often by a licensed HVAC or plumbing contractor.
Prioritized Recommendations
The most useful reports rank improvements by estimated savings, cost, and payback. A typical order for an older Colorado home might be attic air sealing, attic insulation, duct sealing, rim joist and crawl space work, and then equipment upgrades. Below-grade spaces matter here too; the crawl space insulation hub explains how floors, crawl spaces and rim joists fit into the overall envelope.
Test-Out Results
If improvements are made, a second blower door test confirms the result. A meaningful drop in CFM50 verifies that air sealing was done well, and some rebate programs require this test-out.
Common Audit Findings in Front Range Homes
Housing stock along the Front Range spans 1950s ranches in Lakewood and Aurora, 1970s and 1980s split-levels across Jefferson and Arapahoe counties, and newer production homes in Douglas and El Paso counties. Each era tends to produce its own pattern of audit findings.
Older ranches and bungalows often show thin or uneven attic insulation, uninsulated exterior walls, leaky original windows, and unsealed chimney chases. Atmospherically vented furnaces and water heaters are common, which makes combustion testing especially relevant before any tightening work.
Split-levels and bi-levels frequently have comfort imbalances between levels, uninsulated rim joists, and ductwork routed through unconditioned garages or crawl spaces. Bonus rooms over garages are a classic cold-in-winter, hot-in-summer complaint, usually tied to missing insulation and air leakage at the floor and knee walls.
Newer homes usually test tighter, but auditors still find attic hatches without weatherstripping, gaps around recessed lights, bath fans that terminate in the attic, and duct connections that came loose during construction. A tighter house also raises questions about mechanical ventilation and indoor air quality, which an auditor can address.
Colorado’s large day-night temperature swings, strong sun at altitude, and dry winter air all shape the recommendations. Summer attic heat is a real comfort issue in many homes, and winter stack effect in two-story houses pulls cold air in low and pushes warm air out through the attic, which is why the attic floor is so often the first priority.
Energy Audit vs Home Inspection
Buyers sometimes assume a home inspection covers energy performance. It does not, at least not in the measured sense. A home inspection following the ASHI Standards of Practice is a visual assessment of the condition of major systems and components: roof, structure, plumbing, electrical, heating and cooling, insulation and ventilation in accessible spaces, and so on. Inspectors report observed defects and safety concerns; they are not required to measure air leakage, calculate heat loss, or estimate energy savings.
An energy audit goes deeper on performance but narrower on scope. An auditor will not typically evaluate the roof covering’s remaining life, test every outlet, or assess the foundation. The two services complement each other:
| Feature | Home inspection | Home energy audit |
|---|---|---|
| Main purpose | Condition and safety of the whole house | Energy use, comfort, and combustion safety |
| Blower door test | Not standard | Usually included |
| Infrared scan | Sometimes, as an add-on | Common |
| Combustion testing | Visual check of venting | Measured draft and CO |
| Typical timing | During a purchase contingency | Any time, often after move-in |
For a typical purchase, the inspection comes first. The site’s breakdown of home inspection cost explains what that service usually includes and what add-ons are available. Once the home is owned, an energy audit helps plan the upgrades the inspection may have flagged in general terms, such as thin attic insulation or an aging furnace.
Getting the Most From an Audit
A little preparation helps the auditor work efficiently and produces a better report:
- Gather 12 months of gas and electric bills.
- Make a list of comfort problems by room and season.
- Clear access to the attic hatch, crawl space, furnace, and water heater.
- Close fireplace dampers and clean out ashes, since the blower door can pull ash into the room.
- Plan to be home and ask questions during the test; seeing leaks in real time makes the report easier to understand.
- Ask for photos and infrared images in the final report.
After the audit, tackle safety items first, then the cheapest high-impact fixes, usually air sealing and attic insulation, before moving on to equipment or windows.
When to Call a Professional
Schedule a professional audit before major efficiency spending, when comfort problems persist despite basic weatherization, when gas appliances are older or show signs of poor drafting, or when a home has high bills relative to similar homes. If combustion testing flags a backdrafting appliance or elevated carbon monoxide, stop air sealing work and bring in a licensed HVAC contractor before continuing.
More Questions About Home Energy Audits
How long does a home energy audit take?
A professional home energy audit typically takes about two to four hours for an average single-family house, including the blower door test, infrared scan, and inspection of the attic, basement, and mechanical systems. Larger homes, homes with multiple HVAC systems, and audits that include duct leakage and combustion testing can take longer. The written report usually arrives within a few days to two weeks. Homeowners can speed the visit by clearing access to the attic hatch, basement, and furnace before the auditor arrives.
Is there a tax credit for a home energy audit in 2026?
No, the federal tax credit that covered part of the cost of a home energy audit ended for audits completed after December 31, 2025, along with the other energy-efficient home improvement credits. Audits done in 2026 do not qualify. Many utilities still offer free or discounted audits, and some state energy offices and local programs provide rebates for audits and the upgrades that follow. Checking the utility’s website and the state energy office before booking is the best way to find current incentives.
What are the most common findings in a home energy audit?
The most common home energy audit findings are air leaks at the attic floor, rim joists, and around recessed lights, followed by insufficient attic insulation and leaky ductwork in unconditioned spaces. Auditors also frequently find poorly sealed windows and doors, missing weatherstripping on attic hatches, and older heating equipment running below efficiency. Air sealing and attic insulation are usually the most cost-effective fixes. Combustion safety problems, such as backdrafting water heaters, appear less often but are the most important to correct.
How should a house be prepared for an energy audit?
A house should be prepared for an energy audit by clearing access to the attic, basement, crawlspace, furnace, and water heater, and gathering 12 months of utility bills. Close all windows and exterior doors, and shut down fireplaces or wood stoves so ashes are cold, since the blower door test depressurizes the house. Make a list of comfort problems, such as cold rooms or drafts. Tell the auditor about any planned renovations so recommendations can be coordinated with that work.
References
- What to Look For: DIY Checks and Inspections — ENERGY STAR
- Duct Sealing — ENERGY STAR
- ENERGY STAR Rebate Finder — ENERGY STAR
- Introduction to Indoor Air Quality — U.S. Environmental Protection Agency
- ASHI Standards of Practice — American Society of Home Inspectors
Frequently asked questions
What is included in a home energy audit?
A full professional audit usually includes a blower door test to measure air leakage, an infrared scan for missing insulation and air leaks, combustion safety testing on gas appliances, a duct inspection or duct leakage test, and a review of insulation, equipment and utility bills. The result is a prioritized list of improvements.
How much does a home energy audit cost?
Industry estimates suggest a full diagnostic audit commonly runs roughly $200 to $700 for a typical single-family home. Some utilities offer free or discounted audits, so check with your electric and gas providers before booking.
Is a home energy audit worth it?
For homes with comfort problems, high bills, or planned efficiency upgrades, an audit helps direct money toward the most cost-effective fixes. It also includes combustion safety testing, which matters before tightening up a house with gas appliances.
What is a blower door test?
A blower door is a calibrated fan mounted in an exterior doorway that depressurizes the house, commonly to 50 pascals. The airflow needed to hold that pressure measures how leaky the house is, and the pressure difference makes hidden air leaks easier to find.
Does a home inspection include an energy audit?
No. A standard home inspection is a visual assessment of the home's condition and safety. It may note thin insulation or old equipment, but it does not usually include blower door testing, measured combustion testing, or energy savings estimates.
Can a home energy audit find mold?
A home energy audit does not test for mold, but auditors often find moisture issues, such as attic condensation, damp crawlspaces, or bathroom fans venting into the attic, that lead to mold. Infrared scans can reveal damp areas. Suspected mold should be evaluated separately by a mold inspector.
Who performs home energy audits?
Home energy audits are usually performed by energy auditors certified through programs such as BPI or RESNET, and some utilities use approved contractors. Choosing an auditor who does not also sell the recommended upgrades, or who provides independent results, helps ensure unbiased recommendations.
How much can a home energy audit save?
A home energy audit itself saves nothing, but upgrades it recommends, mainly air sealing and insulation, often cut heating and cooling costs by roughly 10 to 30 percent in leaky homes, according to industry estimates. Savings depend on the home's starting condition, climate, and how many recommendations are completed.
Buying a home and want a clear picture of its condition before planning energy upgrades? Front Range buyers can get matched with a qualified local inspector who can flag insulation, ventilation and combustion concerns early.