Skip to content
Independent home-inspection guidance. We are not affiliated with the prior occupant of this domain.
Find an inspector

Fire-Resistant House Materials: Roofs, Siding, Vents and Decks

By InspectandTest Editorial Team Published October 4, 2026 Updated November 12, 2026

We may earn commission from links on this page. Lead-form submissions are forwarded to local inspector partners. How we research and review.

Photo via Unsplash by Chris Karidis

Choosing fire resistant house materials is one of the most practical ways to improve a home’s odds in a wildfire, but the details matter more than the labels. Research summarized by the National Fire Protection Association points to embers and small flames, not a wall of fire, as the main way most homes ignite in wildfires. That shifts attention to the parts of a house embers can reach: the roof, gutters, vents, siding, windows and decks. This guide explains how Class A roof ratings work, what makes a vent ember-resistant, how common siding options compare, what tempered and dual-pane glass contribute, how to handle decks and gutters, where Colorado hail adds a second consideration, and a sensible order for retrofits. It summarizes NFPA Firewise and U.S. Fire Administration guidance as of 2026; local codes and product listings govern actual installations.

Which House Materials Resist Wildfire Best?

The short answer from NFPA’s Firewise tip sheet on preparing a home for wildfire: Class A fire-rated roofing such as composite shingles, metal, concrete and clay tiles; fire-resistant siding such as brick, fiber cement, plaster or stucco; dual-pane tempered glass windows; and roof and attic vents screened to prevent ember entry. The same tip sheet advises keeping flammable materials out from under decks and porches and clearing debris between deck boards.

No material makes a house fireproof. Noncombustible siding will not help much if a woodpile is stacked against it, and a Class A roof can still let embers in through an unscreened vent or a broken tile. Fire resistance is about the whole assembly and how it is maintained, along with the landscaping around it, which is covered in our guide to defensible space.

Component Higher-resistance options Common weak points
Roof Class A assemblies: asphalt/composite shingles, metal, concrete or clay tile Untreated wood shakes, debris in valleys, gaps at ridge and eaves
Vents Metal mesh no larger than 1/8 inch, or ember-resistant listed vents Coarse screens, plastic vents, damaged screens
Siding Fiber cement, stucco or plaster, brick, stone Wood or vinyl siding, gaps at trim and joints
Windows Dual-pane with tempered glass Single-pane annealed glass, vinyl frames near fuels
Decks Noncombustible or ignition-resistant decking, enclosed or screened underside Debris between boards, storage underneath
Gutters Metal gutters, kept clean; metal guards Needle and leaf buildup, plastic guards

Roofs: Why Class A Is an Assembly Rating

The roof is the largest horizontal surface on most homes, which makes it the most likely landing spot for embers. Roof coverings in the U.S. are tested and rated Class A, B or C for fire resistance, with Class A offering the highest resistance to fire exposure from the outside.

An important nuance: many Class A ratings apply to the roof covering installed over specific components, not to the shingle or panel by itself. Some products are Class A on their own; others achieve Class A only when installed over a particular fire-resistant underlayment or deck board, sometimes described as a “Class A assembly.” That is why product listings and installation instructions matter, and why the layer beneath the covering deserves attention during a reroof. Our guide to roof underlayment explains the main underlayment types and where they are used.

Asphalt and Composite Shingles

Most asphalt shingles sold today carry a Class A rating when installed as directed, which is why they appear first on NFPA’s list of Class A products. Their wildfire weak points are usually maintenance-related: loose or missing shingles, debris packed into valleys, and gaps at ridges and edges where embers can lodge. NFPA’s Preparing Homes for Wildfire page specifically recommends replacing or repairing loose or missing shingles or tiles to prevent ember penetration.

Metal Roofing

Metal panels and metal shingles are noncombustible and commonly achieve Class A ratings, often as an assembly over a specified underlayment. Attention goes to the open ends of panel profiles at eaves and ridges, where closures or fillers keep embers and debris out. For costs and panel types, see our guide to metal roof cost.

Concrete and Clay Tile

Tile is noncombustible and listed by NFPA among Class A products. The gaps at the eaves and the open space under curved tiles can collect debris and admit embers unless the ends are closed with bird stops or similar closures. Broken tiles also need prompt replacement.

Wood Shakes

Untreated wood shake roofs are widely regarded as the most vulnerable roof type in wildfire areas. Fire-retardant-treated shakes can achieve higher ratings, but treatment performance depends on the product and its age. Many Colorado jurisdictions with wildfire codes restrict wood roofing in hazard areas, and some insurers ask about it specifically.

Vents, Eaves and Soffits: Stopping Ember Entry

Attic and crawl space vents are essential for moisture control, but every opening is a potential path for embers into the attic, where dry framing and insulation sit. NFPA recommends installing 1/8-inch metal mesh screening over eave and exterior attic vents and keeping them clear of debris. The Firewise tip sheet also suggests boxing in eaves while still providing ventilation to prevent condensation and mildew.

Options for upgrading vents include:

  • Replacing coarse screens with corrosion-resistant metal mesh no larger than 1/8 inch. Smaller openings block more embers but clog faster and reduce airflow, so net free area should be rechecked.
  • Ember- and flame-resistant listed vents that use baffles or intumescent materials. These are often required in local wildfire codes for new construction and can be used in retrofits.
  • Closing open eaves with noncombustible or ignition-resistant soffit material, while maintaining the intake ventilation the attic needs.

Because changes to vents affect how the attic breathes, they should be planned with ventilation in mind. Our guides to attic ventilation and soffit and fascia repair cover intake and exhaust balance and the common problems at the roof edge.

Siding and Exterior Walls

Exterior walls are exposed to embers that collect at the base of the wall, radiant heat from burning vegetation or neighboring structures, and direct flame from anything burning nearby. NFPA’s Firewise tip sheet notes that embers can collect in small nooks and crannies and ignite combustible materials, and it names brick, fiber cement, plaster and stucco as fire-resistant siding choices.

Fiber Cement

Fiber cement lap siding, panels and trim are noncombustible and widely available, and they are a common replacement for wood or vinyl in Colorado. They also hold up reasonably well to hail and sun. Installation details still matter, including flashing, gaps at the base of the wall and the material used for trim. Our guide to Hardie board siding covers the best-known fiber cement brand, costs and maintenance.

Stucco and Plaster

Traditional three-coat cement stucco is noncombustible and performs well against embers and moderate heat. Some synthetic stucco systems include foam insulation boards, so fire performance depends on the specific system. Cracks and damaged areas should be repaired so moisture and embers cannot get behind the finish.

Brick and Stone

Masonry walls and veneers are noncombustible. Weak points are elsewhere: wood trim, combustible soffits, and gaps where the masonry meets windows and the roofline.

The First Few Feet of Wall

Many fire guidance documents emphasize a noncombustible zone at the base of the wall. Some owners use a strip of fiber cement or masonry at the bottom of wood-sided walls and replace mulch with gravel, which combines a material change with immediate-zone landscaping.

Windows and Glass

Radiant heat can crack window glass, and a broken window lets embers and flames into the home. NFPA’s tip sheet recommends dual-pane tempered glass windows. Tempered glass is considerably more resistant to heat-induced breakage than standard annealed glass, and a second pane adds another barrier. NFPA’s Preparing Homes for Wildfire page also advises repairing or replacing damaged or loose window screens and broken windows.

Frame material plays a role too. Vinyl frames can soften and deform under heat, while metal-clad, fiberglass and some wood frames may hold up better, depending on the product. Window replacement is costly, so many owners prioritize windows that face slopes, heavy vegetation or nearby structures.

Decks, Porches and Attachments

Decks are often where wildfire finds its way to a house. Debris collects between boards and underneath, items stored below can ignite, and an attached wood deck carries fire directly to the wall. NFPA advises screening or boxing in areas below patios and decks with wire mesh, and removing anything stored beneath decks and porches. The Firewise tip sheet also calls for removing dead vegetation and debris from under decks and between deck board joints.

Material options include:

  • Noncombustible decking such as aluminum, steel-framed systems, or concrete and stone patios. These are the most resistant but often the most expensive.
  • Ignition-resistant decking, including some fire-retardant-treated wood and certain composite products tested for wildfire exposure. Performance varies widely among composites, so check whether a product has been tested and listed for wildfire areas.
  • Standard wood decking can be made less vulnerable with diligent debris clearing, a noncombustible zone at the house, and enclosing or screening the underside.

Treat fences, pergolas and attached sheds the same way. A wood fence that meets the house can carry fire straight to the siding, so many owners replace the last few feet with metal.

Gutters and Roof Edges

Gutters full of pine needles and leaves act as ember catchers right at the roof edge, where they can ignite fascia, roof sheathing and underlayment. NFPA lists cleaning roofs and gutters of dead leaves, debris and pine needles among the first steps in the immediate zone. Metal gutters are preferable to vinyl in wildfire areas. Metal gutter guards can reduce buildup, but needles may collect on top, so guards reduce cleaning rather than eliminate it.

A drip edge and a noncombustible fascia or fascia cover close another common gap where embers can reach roof sheathing.

Other Openings: Garage Doors, Chimneys and Crawl Spaces

Ember entry points are not limited to attic vents. Several smaller openings get overlooked during retrofits:

  • Garage doors. Gaps along the sides and bottom of an overhead door let embers blow into a space that often holds gasoline, cardboard and other combustibles. Weatherstripping and a bottom seal in good condition narrow those gaps.
  • Chimneys and spark arrestors. A chimney cap with a metal spark arrestor screen helps keep embers from entering the flue and stops sparks from a wood fire from leaving it. Caps should be checked for corrosion and clogging.
  • Crawl space and foundation vents. These sit near ground level, right where windblown embers and debris accumulate. The same 1/8-inch metal mesh approach used for attic vents applies, along with keeping vegetation and mulch away from the openings.
  • Dryer and bath exhaust terminations. Wall and roof caps with dampers that close fully, and that are free of lint buildup, reduce the chance of embers entering through ductwork.
  • Gaps at trim and penetrations. Openings around pipes, wiring and where siding meets the roof or foundation can be sealed with appropriate caulk or noncombustible materials.

None of these items is expensive on its own, and most can be checked during a routine walk around the house.

How to Evaluate Products and Ratings

Marketing terms such as “fire-safe,” “fire-rated” and “fireproof” are not standardized, so look past the label. When comparing products, a few questions help:

  • What exactly was tested? A roof covering may be Class A only over a specific underlayment or deck. A vent may be listed only for a particular orientation. Ask for the listing or test report and read its conditions.
  • Does the local code require it? Front Range counties and fire districts with wildfire codes may require ignition-resistant materials for new work in mapped hazard areas. The building department can say what applies at a given address.
  • How will it age? Fire-retardant treatments, sealants and some coatings can lose effectiveness over time or with weathering. Noncombustible materials generally do not.
  • How does it fit with moisture management? Closing eaves, adding finer vent mesh or changing siding can affect ventilation and drainage. Upgrades should not create condensation or rot problems.

Colorado Factor: Hail and Fire Together

Front Range homes face hail as often as wildfire, and material choices interact. A Class A asphalt roof that has taken repeated hail hits may have bruised or cracked shingles and lost granules, which can open small paths for embers and shorten the roof’s service life. After a significant storm, an evaluation of hail damage to the roof helps determine whether repairs or replacement are due.

When a hail claim leads to a reroof, many owners use the opportunity to upgrade. Impact-rated shingles, metal and some tile products can address both concerns, though impact ratings and fire ratings are separate tests and a product should be checked for both. Siding replacement after hail is a similar opportunity to move from wood or vinyl to fiber cement.

Retrofit Priorities: Where to Start

Budgets rarely allow everything at once. The order below is a general approach drawn from NFPA’s emphasis on the house and the first five feet; the right order for a specific home depends on its construction, slope, vegetation and local fire behavior, so a local fire district mitigation assessment is worth requesting.

  1. Maintenance first: clean roofs and gutters, repair loose shingles or tiles, clear debris from under decks, and move firewood and combustibles away from walls. These steps cost little and address common ember entry points.
  2. Vents: replace damaged or coarse vent screens with 1/8-inch metal mesh or listed ember-resistant vents.
  3. The immediate zone: create a noncombustible strip around the house and under attached decks.
  4. Deck underside and attachments: enclose or screen below decks and break wood fence connections to the house.
  5. Roof replacement: when the roof is due, choose a Class A assembly and close gaps at eaves and ridges.
  6. Siding and windows: upgrade the most exposed walls and windows first, often during other remodeling or after storm damage.

A home inspection can help identify roof, vent, siding and deck conditions before purchase or a retrofit. See our guide to hiring a home inspector and the structure and exterior section for related topics.

More Questions About Fire-Resistant Building Materials

Does fire-resistant construction lower home insurance costs?

Fire-resistant construction can lower home insurance costs or improve insurability in wildfire-prone areas, though discounts vary by insurer and state. Some insurers and state programs recognize mitigation like Class A roofs, ember-resistant vents, noncombustible siding and defensible space. In high-risk regions, these upgrades can make the difference between getting coverage and being declined. Homeowners should document upgrades with receipts, product specifications and photos, and ask their insurer which features qualify for credits before choosing materials.

How much does it cost to make a house fire resistant?

Making a house more fire resistant can range from a few hundred dollars for ember-resistant vent screens and gutter guards to tens of thousands for a new Class A roof, noncombustible siding or replacement windows. Many upgrades are cheapest when done during a scheduled replacement, such as choosing fiber cement siding when the old siding wears out. Defensible space work around the home is often the most cost-effective first step. Prioritizing vents, the roof, the first five feet around the house and decks gives the most protection per dollar.

Are fire-resistant materials required in wildfire zones?

Fire-resistant materials are required in many designated wildfire zones by local building codes, often based on wildland-urban interface standards. Requirements commonly cover Class A roofs, ember-resistant vents, ignition-resistant siding, tempered glass and deck materials. Rules usually apply to new construction and major remodels, not existing homes, but replacing a roof or siding may trigger them. Local building departments and state fire agencies publish maps and code requirements, so homeowners can check their property’s zone before planning upgrades.

Is a metal roof safer in a wildfire?

A metal roof is generally safer in a wildfire than wood shakes or untreated combustible roofing because the metal itself does not burn. Achieving a Class A rating depends on the roof assembly, including underlayment and deck. Gaps at ridge caps, eaves and panel ends must be closed so embers cannot lodge underneath. Debris such as leaves and pine needles that collects on any roof or in gutters can still ignite. Regular cleaning and ember-resistant vents complete the protection a metal roof provides.

References

Frequently asked questions

What is the most fire-resistant roofing material?

NFPA's Firewise guidance lists Class A fire-rated products such as composite shingles, metal, concrete and clay tile as offering the best protection. Many Class A ratings depend on the full assembly, including underlayment, and loose shingles or open eave gaps can still let embers in.

Is fiber cement siding fire resistant?

Yes. Fiber cement is noncombustible, and NFPA's Firewise tip sheet names it alongside brick, plaster and stucco as fire-resistant siding. Trim, gaps and anything combustible stored against the wall remain potential weak points.

What size mesh keeps embers out of attic vents?

NFPA recommends 1/8-inch metal mesh screening over eave and attic vents. Smaller mesh blocks more embers but can clog and reduce airflow, so vent area and cleaning should be checked, and listed ember-resistant vents are another option.

Are composite decks fire resistant?

It depends on the product. Some composites have been tested and listed for wildfire areas while others perform poorly, so check for wildfire-related testing. Regardless of material, keep debris out from between boards and under the deck and do not store items below.

Do tempered windows help in a wildfire?

NFPA recommends dual-pane tempered glass because radiant heat can crack windows and let embers and flames inside. Tempered glass resists heat-induced breakage better than standard glass, and frame material and screens also affect performance.

Are vinyl windows fire resistant?

Vinyl window frames can soften and deform in high heat, which may let glass fall out during a wildfire. Dual-pane windows with tempered glass perform better, and metal-reinforced or fiberglass frames hold up longer. Window choice is one part of an overall ember and heat-resistant plan.

Is stucco fire resistant?

Yes. Traditional cement stucco is noncombustible and performs well against wildfire exposure, especially over a fire-resistant wall assembly. Foam-based exterior insulation finish systems behave differently and may need careful detailing. Gaps, vents and openings remain weak points regardless of siding.

What is the first thing to do to make a home fire resistant?

The first thing to do is clear the zone within about 5 feet of the house of combustibles like mulch, firewood, dry plants and debris, and clean roofs and gutters. These low-cost steps reduce ember ignition near walls, decks and vents, which is how many homes catch fire.

Planning a reroof, siding upgrade or purchase in a wildfire-prone area? Get in touch to schedule an inspection that documents roof, vent, siding and deck conditions before you decide.