Skip to content
Independent home-inspection guidance. We are not affiliated with the prior occupant of this domain.
Find an inspector

Stove Anti-Tip Brackets: The Child Safety Part Often Missing

By InspectandTest Editorial Team Published October 5, 2026 Updated November 12, 2026

We may earn commission from links on this page. Lead-form submissions are forwarded to local inspector partners. How we research and review.

Photo via Unsplash by Shahabudin Ibragimov

A freestanding kitchen range looks heavy and solid, and most of the time it is. Open the oven door, though, and the balance changes. The door becomes a lever sticking out from the front of the appliance, and enough weight on it can pull the whole range forward. A child standing on the door to see what is cooking, a heavy roasting pan set on the door, or an adult leaning on it while cleaning can all supply that weight. The anti-tip bracket is a small piece of metal, screwed to the floor or wall behind the range, that keeps a rear leg from lifting. It costs very little, it is often included in the box with a new range, and it is frequently missing, loose or disengaged in existing homes. This guide explains how tip-overs happen, what federal safety data and recalls show, how to check whether a bracket is doing its job, how to reinstall one after moving or replacing a range, and how the bracket fits into wider childproofing.

What a Stove Anti-Tip Bracket Does

A stove anti tip bracket is a small steel bracket that anchors the back of a freestanding or slide-in range to the building. Most brackets fall into one of two designs:

  • Leg-capture brackets. An L-shaped or box-shaped bracket screwed to the floor, positioned so one rear leveling leg slides underneath a lip when the range is pushed back. If the front of the range is pulled down, the lip holds the rear leg against the floor.
  • Wall- or rear-panel brackets. A bracket fastened to the wall or to the floor at the wall that engages a slot or the back edge of the range. Some ranges use a bracket that engages the back panel rather than a leg.

In both cases the bracket only works when the range is fully pushed back and the leg or panel is actually engaged. A bracket screwed to the floor six inches to the left of the leg does nothing. Neither does one that came loose when the range was pulled out for cleaning, or one whose screws were driven into nothing but vinyl flooring.

How a range tips over

When the oven door is closed, the range’s center of gravity sits well inside its footprint. When the door opens, anything placed on it sits in front of the front legs. Because the door is long, a modest load at the outer edge can exert a large turning force. If that force is greater than the range’s own weight working the other way, the rear lifts and the range rotates forward. Hot cookware on the cooktop can slide off, and pots of boiling water or oil can spill onto whoever is in front of it. The range itself can land on a small child.

What CPSC Data and Recalls Show

The U.S. Consumer Product Safety Commission tracks tip-over incidents involving televisions, furniture and appliances. In its 2023 tip-over report, published in February 2024, CPSC staff counted 217 reported tip-over fatalities from January 1, 2013 through July 31, 2023, and 155 of those, or 71 percent, involved children under age 18. Of the 217 deaths, 15 involved only an appliance falling, and CPSC reported that 9 of those involved a stove or oven and 6 involved a refrigerator. CPSC also estimated an annual average of about 600 emergency department-treated injuries involving appliance-only tip-overs for 2020 through 2022. The report notes that fatality counts for recent years should be considered incomplete because of reporting lags, and it lists non-use of a tip-over restraint device among the factors that can contribute to instability.

Recalls tell a similar story about how the hazard works. In December 2021, CPSC announced that GE Appliances, a Haier company, was recalling about 132,000 free-standing and slide-in electric and gas ranges sold under several brand names. The hazard description stated that the ranges can tip over when a heavy object is placed on an open oven door and the anti-tip-over bracket is not secured to the wall or floor, posing a tip-over hazard and risk of burn injuries from hot food or liquids in cookware. The remedy was a free in-home service call to inspect the anti-tip bracket and make sure it was securely installed, and owners were cautioned not to place objects on the open oven door until that was done. No incidents or injuries were reported in that recall.

In March 2022, CPSC announced a recall by Danby Products of about 1,700 free-standing and slide-in electric and gas ranges, with nearly identical hazard language and the same type of remedy. Again, no incidents or injuries were reported. Both recalls highlight the same point: a range’s stability on an open door depends on the bracket being installed and secured.

How to Check That the Bracket Is Engaged

Many homeowners have never seen their anti-tip bracket because it sits behind or under the range. Checking takes only a few minutes. The appliance owner’s manual is the best guide for the specific model, and many manufacturers include a check procedure.

  1. Look for the bracket. Remove the storage or warming drawer, if the range has one, and use a flashlight to look at the floor near the back corners. A metal bracket near one rear leg is a good sign.
  2. Confirm the leg is under the bracket. From the drawer opening, see whether the rear leveling leg is actually tucked under the lip of the bracket rather than sitting beside it.
  3. Do a gentle tilt check. Many manufacturers describe grasping the top rear edge of the range and carefully trying to tilt it forward. If the range stops almost immediately, the bracket is likely engaged. If the back lifts freely, it is not. Do this only with the cooktop and oven off and cool, nothing on the cooktop, and no one standing in front of the range.
  4. Check the fasteners. Screws should be driven into solid material: wood subfloor, framing, or concrete using appropriate anchors. A bracket held only by thin flooring or drywall may pull free under load.

Do not test by standing on or loading the oven door. That is exactly the scenario the bracket is meant to prevent, and a failed test could cause injury.

Common problems found in existing homes

  • No bracket at all, often because an older range was installed before brackets were routinely supplied or because the bracket was left in the box.
  • A bracket installed for a previous range that does not line up with the current range’s leg or slot.
  • A range pulled forward for cleaning, flooring work or a gas connection and pushed back without re-engaging the leg.
  • Leveling legs raised or lowered so the leg no longer fits under the bracket lip.
  • Bracket screws loosened or stripped, especially over tile or thick underlayment.

Renters, landlords and flips

Rental units and recently renovated houses deserve a specific look. Appliances in rentals are often replaced quickly between tenants, and the person delivering the range may not be the person responsible for the floor or the wall behind it. In flipped houses, new flooring is frequently installed after the old range is pulled out, and the new range may go in without anyone revisiting the bracket. Tenants with young children can reasonably ask the landlord or property manager to confirm the bracket is installed and engaged. Landlords may find it simpler to check every range during turnover inspections, since the fix is quick and inexpensive.

Range Types and Where Brackets Apply

Not every cooking appliance carries the same tip risk, and the way it is secured differs by type:

  • Freestanding ranges. The most common type in Front Range homes. They have finished sides and a backguard with controls, and they rely on the anti-tip bracket for stability with the door open.
  • Slide-in ranges. Designed to sit flush between cabinets with controls on the front. They still stand on their own legs and are typically supplied with an anti-tip device. The tight fit between cabinets does not by itself hold the range down.
  • Drop-in ranges. Less common today, these sit on a cabinet base or are supported by the countertop and are secured according to the manufacturer’s instructions.
  • Wall ovens and cooktops. A wall oven is fastened into a cabinet, and a cooktop is mounted in the countertop, so the open-door tipping scenario does not apply the same way.
  • Compact and apartment-size ranges. Narrower 20- and 24-inch ranges are lighter, which can make them easier to tip. Both recalls described above included ranges in these smaller widths.

Weight also changes over time. A range with an empty storage drawer and nothing on the cooktop is lighter and easier to rotate than one loaded with cast-iron cookware. That is one reason the bracket matters even on ranges that feel heavy when pushed.

Double-oven ranges and models with large, heavy doors place even more leverage at the front edge when the lower door is opened. The same applies to ranges with pull-out warming drawers, which children sometimes use as a step. Checking the bracket is a good habit on any range that can be pulled away from the wall without disconnecting anything rigid.

Installing a Bracket After Moving or Replacing a Range

The bracket is model-specific in its position, so a new range usually needs a new bracket in a new location. The manufacturer’s installation instructions show the exact distance from the side cabinets and the wall. General steps include:

  • Use the template or measurements in the instructions to mark the bracket position for the specific range.
  • Check for hidden pipes, wiring and in-floor heating before drilling. Gas lines and electrical cables often run near the range.
  • Fasten the bracket into solid material with the screws or anchors supplied, or with anchors suited to concrete or tile.
  • Adjust the leveling legs, then slide the range back, making sure the rear leg goes under the bracket and the cord, gas connector and water lines are not pinched.
  • Repeat the gentle tilt check described above.

Gas ranges add another layer. Moving a gas range can stress or kink the flexible connector, and reconnecting gas should be done by someone qualified, followed by a leak check. Our gas stove installation guide covers connectors, shut-off valves and ventilation. If the project includes new ventilation, the range hood installation guide explains ducting and makeup air considerations.

Appliance retailers that install new ranges typically include the bracket in the installation, but it is worth asking specifically and checking afterward. Delivery crews sometimes leave the bracket in the packaging or skip it when the floor surface makes drilling awkward.

The Bracket as Part of Wider Childproofing

An anti-tip bracket addresses one specific hazard, but it fits into a broader approach to tip-overs and kitchen safety in homes with young children. CPSC’s tip-over report found that televisions and furniture account for most tip-over injuries and deaths, so the same household that needs a range bracket usually benefits from anchoring dressers, bookcases and TVs. Our furniture anchors guide covers the types of straps and brackets and how to fasten them into studs.

Other steps families often take in the kitchen:

  • Use back burners when possible and turn pot handles toward the wall.
  • Keep step stools and chairs away from the range.
  • Use knob covers or a range with lockout features if toddlers can reach the controls.
  • Install latches on lower cabinets that hold cleaning products or sharp items. Our cabinet locks guide compares common styles.
  • Block stairs and keep kitchens gated during cooking where practical. The baby gate for stairs guide explains why hardware-mounted gates belong at the top of stairs.

Childproofing works best as a set of overlapping layers. No single device prevents every incident, and supervision remains the most important factor.

Costs and Hiring

An anti-tip bracket is one of the least expensive safety fixes in a house. As a rough 2026 guide:

  • Replacement bracket: often a few dollars to around $20 to $30 for a manufacturer-specific bracket ordered through a parts supplier, or included free with a new range.
  • Do-it-yourself installation: usually under an hour for an electric range with a wood subfloor, longer over tile or concrete.
  • Appliance technician or handyman visit: commonly a service-call charge, often in the low hundreds of dollars, especially if the range must be disconnected.
  • Gas range disconnection and reconnection: may add cost for a gas-qualified technician and leak testing.

Some retailers include bracket installation in their standard delivery and haul-away fee. Manufacturers and CPSC recall notices are also worth checking, since recalled ranges may qualify for a free in-home bracket inspection.

When ordering a replacement, the range’s model number is the key piece of information. It is usually printed on a label inside the storage drawer opening, on the oven frame, or behind the door. Universal brackets exist, but a manufacturer-specified part with the matching instructions is generally the safer choice because the bracket position depends on the leg or slot design.

What a Home Inspection Covers

The ASHI Standard of Practice directs inspectors to inspect installed ovens, ranges and surface cooking appliances by using normal operating controls to activate the primary function. That means turning on burners and the oven to see whether they heat. The standard does not specifically list anti-tip brackets, and checking for one usually means removing the drawer or attempting a tilt test, which some inspectors do as a courtesy and others do not. Inspectors who check commonly report a missing or disengaged bracket as a safety concern with a simple correction.

Because practices vary, it is reasonable to ask the inspector ahead of time whether the anti-tip bracket is part of the kitchen check, and to verify it yourself after moving in. Our heating and cooling inspections section covers the gas and venting side of fuel-burning equipment, and the guide to hiring a home inspector explains how to compare inspectors and what questions to ask.

More Questions About Stove Anti-Tip Brackets

Are stove anti-tip brackets required by law?

Anti-tip brackets are required by the product safety standard for freestanding ranges, which since 1991 has called for ranges to include an anti-tip device and installation instructions. Whether the bracket is actually installed depends on the installer, and enforcement in existing homes is limited.

Manufacturers’ installation instructions require the bracket, and building inspectors may check it in new construction. Many retailers include installation in delivery, but brackets are often skipped or left disengaged after a range is moved for cleaning. Homeowners and landlords should verify engagement rather than assume it.

Can a stove tip over without the oven door open?

A stove rarely tips over with the oven door closed, but it can happen if a range is pulled forward, sits on an uneven floor or has heavy items placed on top while it is out of position. The most dangerous scenario is weight on the open oven door.

A child climbing on the open door, or an adult leaning on it to reach the back, can shift enough weight forward to tip an unsecured range. Hot cookware on the cooktop can then fall onto the person. An engaged anti-tip bracket prevents the tipping motion regardless of what causes it.

Will an anti-tip bracket damage tile flooring?

Installing an anti-tip bracket usually means drilling small holes into the floor or wall, which can crack tile if done carelessly. With a masonry or tile bit, light pressure and no hammer setting, the risk is low.

Many brackets can be mounted to the wall behind the range instead, anchored into a stud or the wall plate, which avoids drilling through tile. Placing a piece of painter’s tape over the drill spot helps keep the bit from wandering. Because the range covers the area, any small chip near the hole is normally hidden.

What happens if a stove tips over?

When a stove tips over, the person on the oven door can be crushed or pinned, and hot food, boiling water or cookware on the cooktop can cause serious burns. Children are at greatest risk.

A tipping gas range can also strain or damage its gas connector, raising the risk of a gas leak, and an electric range can damage its power cord. If a range has tipped, have the gas connection or electrical connection checked before using it again, and install or re-engage the anti-tip bracket before pushing it back into place.

Are stove anti-tip brackets universal?

Many anti-tip brackets are sold as universal and fit a range of models, but the safest choice is the bracket designed for the specific range. Range feet, leg positions and back designs differ between brands and models.

The range’s installation manual shows the bracket location and how the rear leg or back panel should engage it. Using a universal bracket that does not line up with the leveling leg may leave the range unsecured even though a bracket is installed. Contact the manufacturer for a replacement part if the original is missing.

References

Frequently asked questions

How do I know if my stove has an anti-tip bracket?

Remove the bottom drawer and look near the rear corners with a flashlight for a metal bracket over a rear leg. Many manuals also describe carefully trying to tilt the range forward from the back edge with everything off and cool; if it stops almost at once, the bracket is likely engaged.

Do all ranges need an anti-tip bracket?

Freestanding and slide-in ranges are generally supplied with an anti-tip device and installation instructions that call for it. Wall ovens and built-in cooktops are secured differently. Check the manual for your specific model.

Can I reuse the old bracket with a new range?

Usually not. Bracket position and style depend on the range model, so a new range normally needs its own bracket installed according to its instructions.

Will a home inspector check the anti-tip bracket?

It depends on the inspector. The ASHI standard requires operating installed ranges but does not specifically list anti-tip brackets, so ask ahead of time and verify it yourself after moving in.

How much does it cost to install a stove anti-tip bracket?

The bracket often costs a few dollars to roughly $20 to $30, or comes free with a new range. A technician visit is commonly a service-call charge, with more if a gas range must be disconnected. These are general 2026 ranges.

How long does it take to install a stove anti-tip bracket?

Installing a stove anti-tip bracket typically takes about 15 to 30 minutes for a homeowner with a drill and basic tools. Most of the time goes into sliding the range out, marking the bracket position and checking that the rear leg engages after the range is pushed back.

Do wall ovens need anti-tip brackets?

No. Built-in wall ovens are fastened into cabinetry and do not need anti-tip brackets. The brackets are for freestanding and slide-in ranges, which sit on the floor and can tip forward when weight is placed on an open oven door.

Can a renter install a stove anti-tip bracket?

A renter should ask the landlord to install a missing anti-tip bracket, since the appliance and its safe installation are usually the landlord's responsibility. If the landlord agrees, a renter may install it, but drilling into floors or walls should be approved in writing first.

Do you need to remove the anti-tip bracket to clean behind the stove?

No. The bracket stays fastened to the floor or wall, and the range simply slides out of it. After cleaning, push the range back carefully so the rear leg slides under or into the bracket, then tilt-test it to confirm the bracket is engaged again.

Moving into a home with little ones? Get in touch to find a Front Range inspector who will look at the kitchen, gas appliances and other child-safety details before you close.