Skip to content
Independent home-inspection guidance. We are not affiliated with the prior occupant of this domain.
Find an inspector

Skylight Installation Cost: Fixed, Vented and Tubular Units

By InspectandTest Editorial Team Published October 18, 2026 Updated November 13, 2026

We may earn commission from links on this page. Lead-form submissions are forwarded to local inspector partners. How we research and review.

Photo via Unsplash by Claudio Mezzasalma

Skylight installation cost depends mostly on the type of unit and how much roof and ceiling work it takes to get light into the room. As a typical national range for 2026, a tubular skylight often runs about $500 to $1,500 installed, a fixed deck-mounted skylight about $1,500 to $3,500, and a venting or solar-powered opening skylight about $2,000 to $5,000 or more, with a new framed light shaft through an attic adding significantly to any of those. Replacing an existing skylight in the same opening usually costs less than cutting a new one. This guide explains what each figure includes, what makes a quote rise, how to decide between repairing, replacing or adding, what Front Range hail and winters mean for skylights, and how to tell whether a quote is complete. Figures here are typical ranges only, so collect written quotes from local roofing or skylight contractors before deciding.

Roof damage or a roof replacement? Get a local roofer on the phone.

📞 Call (833) 850-2469

Free, no-obligation quote · Connect with a local pro. Calls may connect you with a partner contractor; we may be compensated for calls.

Typical Skylight Installation Cost at a Glance

Skylight prices bundle three things: the unit, the roof work (cutting, framing, flashing and reshingling) and the interior work (shaft, drywall and paint). The table separates the common job types so you can see where a quote should land.

Job type Typical national range, 2026 (get local quotes) Main cost drivers
Tubular skylight (sun tunnel), 10–14 inch About $500–$1,500 installed Tube length, elbows, roof pitch, attic access
Fixed skylight, new opening, vaulted ceiling (no shaft) About $1,500–$3,500 installed Unit size, glazing, rafter cutting and headers
Venting skylight, manual or electric About $2,000–$5,000+ installed Motor, rain sensor, wiring, blinds
New light shaft through an attic Often adds about $1,000–$3,000+ Shaft length, flare, insulation, drywall finish
Replace skylight in existing opening About $1,000–$3,000 installed Curb condition, new flashing kit, roof patching
Reflash or reseal a leaking skylight About $300–$1,000 Roof material, extent of shingle removal, decking damage

These ranges assume an ordinary asphalt shingle roof at a walkable pitch. Tile, metal, slate and steep roofs cost more. Interior drywall repair, painting and any electrical work for an opening unit may be listed separately. If you are replacing rather than adding, start with our guide to skylight replacement, which covers when an old unit has reached the end of its useful life.

What Drives the Price of a Skylight Job

Most of the cost lives in labor and in what the installer finds once the roof is open.

Skylight type

Tubular skylights are the least invasive. A small dome sits on the roof, a reflective tube runs through the attic, and a diffuser mounts in the ceiling. No rafters are cut in most cases. Fixed skylights cost more because they need a framed opening, a curb or deck mount and full flashing. Venting units add hardware and, for electric or solar models, wiring or a solar panel, a remote and often a rain sensor that closes the unit when it starts to rain.

Roof framing and pitch

A skylight that fits between existing rafters is simpler. A larger unit that requires cutting a rafter means installing headers and possibly doubling adjacent rafters, which adds carpentry time. Engineered trusses are a different story; they should not be cut without an engineer’s guidance, which can limit size and placement. Steeper roofs need more safety setup and slow the job down.

Roofing material

Asphalt shingles are the easiest to work around. Tile, slate, wood shake and standing-seam metal roofs require more careful removal, special flashing and sometimes a specialist. If the roof is near the end of its life, installing a skylight just before a reroof means paying for flashing twice.

The light shaft

With a vaulted ceiling, the skylight opens straight into the room. With an attic in between, a shaft has to be framed, insulated, drywalled and finished from the roof to the ceiling. A splayed or flared shaft spreads light more widely but takes more material and labor. The shaft is frequently the largest single labor item in a new skylight project.

Glazing and features

Laminated or tempered glass, low-emissivity coatings, tints, built-in blinds and impact-resistant options all raise the unit price. Many buyers in hail-prone areas weigh tempered or laminated glass and sturdier domes more heavily than they would elsewhere.

Permits and hidden damage

Cutting a new roof opening often requires a building permit. Check with your city or county building department. When an old skylight is removed, installers sometimes find rotted decking or framing from years of slow leaks. A good quote states how such repairs will be priced.

Repair, Replace or Add: Making the Call

Many skylight calls start with a stain on the ceiling. Before paying for a new unit, figure out what actually failed.

When repair is enough

Leaks around a skylight are often caused by flashing, not the unit itself. Lifted shingles, failed sealant, missing step flashing or a cracked curb seal can let water in while the glass and frame remain fine. Our guides to skylight leaks and step flashing explain how to tell a flashing failure from condensation or a failed seal in the glass.

When replacement makes more sense

  • The insulated glass has fogged between panes, meaning the seal has failed
  • The frame is cracked, warped or rotting
  • An acrylic dome is crazed, yellowed or brittle
  • The unit is older and the roof is being replaced anyway
  • Repeated reflashing has not stopped the leak

As a rule of thumb, if a repair would cost more than about a third to half of a full replacement on an older skylight, replacement usually offers better value, especially if it can be scheduled with a reroof. That is a rule of thumb, not a standard. A roofer should confirm the condition of the curb and decking.

Adding a new skylight

New skylights are a lifestyle decision as much as a cost decision. They bring daylight into dark hallways, bathrooms and kitchens, but every roof opening is another detail that must stay watertight for decades. In a room that only needs a modest amount of light, a tubular skylight may deliver most of the benefit for a fraction of the cost and risk.

Energy Performance and Ratings to Check

A skylight is effectively a window in the roof, and roofs face the full winter sky and summer sun. ENERGY STAR certifies residential windows, doors and skylights. Its criteria page explains that certified products are independently tested, certified and verified by the National Fenestration Rating Council (NFRC) and have NFRC ratings that meet efficiency guidelines set by the EPA, with performance criteria that vary by climate zone.

Practical points for buyers:

  • Look for both labels. ENERGY STAR advises looking for the ENERGY STAR label for your climate zone next to the NFRC label on the product.
  • Compare U-factor and solar heat gain. Lower U-factor means less heat loss. Solar heat gain matters a lot for south- and west-facing skylights that can overheat rooms in summer.
  • Ask for a labor and materials split. ENERGY STAR notes that different dealers may quote different prices for the same product and suggests asking contractors to break down quotes by labor and materials.
  • Check incentives. ENERGY STAR points to utility rebates and tax incentives for certified windows, doors and skylights. Eligibility changes over time, so confirm current rules before counting on any credit.

Installation quality matters as much as the product. ENERGY STAR warns that even the best windows, doors and skylights can be drafty if they are poorly installed, and that some manufacturers will void the warranty if their installation instructions are not followed. Ask whether the installer is certified by the manufacturer.

Front Range Factors: Hail, Snow and Dry Winters

Colorado’s Front Range puts skylights through conditions that deserve a line in any quote.

  • Hail. Hailstorms are a regular feature of summers along the Front Range. Domed acrylic and older plastic units can crack, and flashing can be dented. Ask about impact-resistant glazing, and check what your homeowners policy covers for roof and skylight damage.
  • Snow and ice dams. Snow sliding down and refreezing around the uphill side of a skylight is a classic leak point. Proper underlayment, a correct flashing kit and good attic insulation and ventilation all help.
  • Freeze-thaw cycles. Repeated freezing and thawing work sealants loose over time. Sealant alone is not a substitute for properly lapped flashing.
  • Strong sun at altitude. High UV exposure ages acrylic domes, gaskets and blinds faster. South-facing skylights may need low solar-gain glass or shades to avoid summer overheating.
  • Condensation in winter. Even in a dry climate, warm indoor air meeting cold glass can condense, especially in bathrooms and kitchens. Drips from condensation are often mistaken for roof leaks.

Our guide to roof flashing explains how skylight flashing ties into the rest of the roof and why replacement flashing kits matter.

Choosing Size, Placement and Skylight Type

The cheapest skylight to own is one sized and placed so it never needs a second project to fix glare, overheating or leaks. A few planning choices affect both the installed price and long-term costs.

Sizing rule of thumb

A commonly used rule of thumb is to keep skylight glass area to roughly 5% of the floor area in rooms with plenty of windows, and up to about 15% in rooms with few windows. For a 12 by 15 foot kitchen (180 square feet) with one small window, that suggests something like 9 to 27 square feet of skylight, which might be one larger unit or two smaller ones. This is a rule of thumb only. Orientation, roof pitch, shading from trees and the purpose of the room all change the right answer, and oversized skylights are a common cause of summer overheating and winter heat loss.

Placement on the roof

  • North-facing slopes give soft, even light with less heat gain.
  • South- and west-facing slopes deliver more light and more heat; they benefit most from low solar-gain glass or shades.
  • Avoid valleys and areas below dormers where water and snow collect, since these are harder to flash and more prone to leaks.
  • Keep clear of plumbing vents and flues so the flashing for each penetration can be done properly.

Comparing the three main types

Feature Tubular Fixed Venting
Typical installed cost Lowest Middle Highest
Roof opening Small, usually no rafter cuts Framed opening Framed opening plus hardware
View of the sky No Yes Yes
Ventilation No No Yes, manual or powered
Best fit Hallways, baths, closets Living areas, vaulted ceilings Bathrooms, kitchens, upper floors that trap heat
Maintenance Dome cleaning, seal checks Glass cleaning, flashing checks Plus motor, sensor and seal checks

Ongoing costs to budget for

Skylights add a few recurring costs that are easy to forget: occasional cleaning of the exterior glass or dome, periodic checks of flashing and seals (often during routine roof maintenance), shade or blind replacement, and for powered units, battery or motor service. When the roof is replaced, budget for new skylight flashing at minimum and, for an older unit, consider replacing the skylight at the same time so its lifespan lines up with the new roof. If a stain has already appeared, our guide to a roof leak covers how to track the water back to its source before paying for repairs.

How to Read a Skylight Quote

Get two or three written quotes and line them up side by side. They should describe the same job so the prices can be compared fairly.

What a complete quote includes

  • Skylight make, model, size, glazing type and whether it is ENERGY STAR certified for your climate zone
  • Mount type (curb or deck) and the specific flashing kit
  • Underlayment and shingle work around the opening
  • Framing work, including any headers or rafter modifications
  • Light shaft construction, insulation and drywall finish, if applicable
  • Electrical work for venting units, and who performs it
  • Permit, debris removal and cleanup
  • How rotted decking or framing will be priced if found
  • Labor warranty, separate from the manufacturer warranty

Red flags

  • Reusing old flashing on a replacement unit
  • “Tar it and forget it” repairs that rely on roofing cement instead of correct flashing
  • No mention of a permit for a new roof opening
  • Cutting trusses without engineering
  • Storm-chaser pressure after hail, such as door-to-door offers to “handle everything with insurance” and sign today
  • Bundled “whole-roof” upsells without photos or evidence of damage beyond the skylight

Questions to ask

  • Is the leak from flashing, the unit, or condensation, and how did you determine that?
  • Will you install a new manufacturer flashing kit?
  • Are you certified by the skylight manufacturer, and does that affect the warranty?
  • How will the shaft be insulated and air sealed?
  • What does your labor warranty cover, and for how long?

If the roof itself needs attention, compare against our guide to roof repair cost before agreeing to bundle work.

Moisture, Mold and Leak Damage

A slow skylight leak can soak drywall, insulation and framing for months before a stain appears. The EPA states plainly that “the key to mold control is moisture control,” and it advises drying water-damaged areas and items within 24 to 48 hours to prevent mold growth. If a skylight has been leaking, the repair quote should include checking the shaft, insulation and decking for wet or damaged material, not just sealing the outside.

Signs that leak damage has gone beyond the skylight include soft or stained drywall in the shaft, sagging ceiling paint, musty odors, dark staining on roof decking visible from the attic, and wet or matted insulation around the opening. Those findings may call for a roofer and, in some cases, a moisture or mold assessment.

How a Home Inspection Flags Skylight Problems

The ASHI Standard of Practice lists “skylights, chimneys, and roof penetrations” among the roofing items an inspector shall inspect, along with roofing materials, roof drainage systems and flashing. Inspectors typically look at a skylight from inside and, where safe and accessible, from the roof or the ground. Common findings include:

  • Water stains on the shaft or ceiling around the skylight
  • Fogged insulated glass from a failed seal
  • Cracked or crazed domes, often after hail
  • Missing, lifted or sealant-patched flashing
  • Debris buildup on the uphill side of the curb
  • Wet insulation or stained decking in the attic near the opening

An inspection is visual and cannot confirm whether a dry stain is old or active, so the usual recommendation for any skylight concern is evaluation by a qualified roofer. If you are buying a home with skylights, or you have spotted a ceiling stain and want an independent view before hiring a contractor, contact our team to book a Front Range inspection.

More Questions About Skylight Installation Cost

Is there a tax credit for installing a skylight?

No, the federal energy-efficient home improvement credit that once applied to qualifying ENERGY STAR skylights ended for work completed after December 31, 2025. Skylights installed in 2026 do not qualify for that federal credit. Some utilities and state energy programs still offer rebates or financing for efficient windows, skylights or related upgrades, though programs change often. Rebate programs often require ENERGY STAR certification for the local climate, so keep the product label and installation invoice.

How long does skylight installation take?

A tubular skylight can often be installed in a few hours to one day. A fixed or venting skylight in a new roof opening typically takes one to three days, including framing the opening, flashing, installing the light shaft and finishing drywall. Painting and finish work can add another day or two. Weather matters, since the roof is open during installation, and permit inspections or roof repairs found during the job may extend the schedule.

Does adding a skylight raise home value?

A well-installed skylight can make a dark room, hallway or bathroom more appealing to buyers, but it rarely returns its full cost in sale price. Buyers notice natural light and may see a skylight as an upgrade, while a skylight with water stains around it can raise concerns about leaks. Value depends on the room, roof condition, quality of flashing and local market. Installing skylights during a roof replacement keeps costs lower and reduces leak risk.

Does homeowners insurance cover skylight leaks?

Homeowners insurance may cover water damage from a skylight leak when it is caused by a sudden covered event, such as hail cracking the glass or a fallen branch. Gradual leaks from worn flashing, failed seals or poor installation are usually treated as maintenance and excluded. Hail damage claims are common in hail-prone regions. Documenting the damage with photos and inspecting skylights after major storms help support a claim if one becomes necessary.

References

Frequently asked questions

How much does it cost to install a skylight?

As a typical national range, a tubular skylight often runs about $500 to $1,500 installed, a fixed skylight about $1,500 to $3,500, and a venting skylight about $2,000 to $5,000 or more. A framed light shaft through an attic adds to any of these.

Is it cheaper to replace a skylight than install a new one?

Usually yes. Replacing a unit in an existing opening avoids cutting rafters and building a new shaft. The installer should still use a new flashing kit and check the curb and decking for rot.

Do skylights always leak eventually?

No. Most leaks trace back to flashing, sealant or installation errors rather than the skylight itself. A correctly flashed skylight with periodic inspection can stay watertight for many years, though seals and domes do age.

Are tubular skylights worth it?

For hallways, bathrooms and closets, a tubular skylight can bring in useful daylight at a fraction of the cost of a full skylight, with a smaller roof opening. It does not provide a view or ventilation.

Do skylights need a permit in Colorado?

Cutting a new roof opening often requires a building permit, but rules vary by jurisdiction. Check with your city or county building department before work begins, and ask the contractor who will obtain the permit.

Can a skylight be installed on a flat roof?

Yes, skylights can be installed on flat or low-slope roofs using a curb-mounted unit, often with a domed or sloped glazing that sheds water. The curb raises the skylight above the roof surface, and the roofing membrane must be properly sealed around it.

What size skylight should I get?

A common rule of thumb is a skylight area of about 5 percent of the floor area in rooms with many windows, and up to about 15 percent in rooms with few windows. Oversized skylights can cause overheating and glare.

Can a skylight be added to a cathedral ceiling?

Yes, a cathedral ceiling is often one of the easiest places to add a skylight, because no light shaft through an attic is needed. The installer must cut and frame the rafters carefully and maintain insulation and ventilation around the opening.

Seeing a stain around a skylight in a home you are buying? Get in touch with our team to arrange a Front Range home inspection.