Best Skylight (2026): Types, Costs + What to Check
The best skylight is one sized and placed to light the room without overheating it, glazed with insulated low-e glass that meets ENERGY STAR’s criteria for your climate zone, and installed with the manufacturer’s own flashing kit so it never leaks. For most Colorado Front Range homes that means choosing between a fixed skylight for pure light, a venting skylight where you also want to let heat and moisture out, and a tubular skylight (often called a solar tube) when the attic space is deep or the budget is small. At altitude, strong sun, hail, heavy spring snow and freeze-thaw cycles all punish the roof penetration, so the flashing and installer matter at least as much as the skylight itself. A note on method: we don’t test skylights or rank brands on reliability. This guide explains how to choose and what to check, using ENERGY STAR criteria and standard roofing practice rather than our own product testing.
Part of our Structure & Exterior guide — start there for the full picture →
This page contains affiliate links; we may earn a commission at no extra cost to you.
Quick Decision Table: Fixed vs Venting vs Tubular Skylights
The bands below are typical installed costs in 2026 for one standard-size unit on an asphalt-shingle roof with reasonable attic access. They rise with steep or tile roofs, metal roofing, larger sizes, laminated or tinted glass, integrated blinds, and especially with the interior light shaft, which needs framing, drywall, insulation and paint between the roof and the ceiling.
| Type | Who it suits | Typical installed price | Key spec to check |
|---|---|---|---|
| Tubular skylight (solar tube) | Hallways, bathrooms, closets; deep attics; small budgets | Typical $500–$1,500 | Dome material, tube reflectivity, insulated diffuser, flashing base |
| Fixed skylight, deck-mounted | Rooms that need daylight but no ventilation; most new installs | Typical $1,200–$3,000 | NFRC U-factor, laminated interior pane, manufacturer flashing kit |
| Fixed skylight, curb-mounted | Low-slope roofs, replacing an existing curbed unit | Typical $1,000–$2,800 | Curb height and insulation, flashing over the curb |
| Manual venting skylight | Within reach of a pole: kitchens, bathrooms, lofts | Typical $1,500–$3,500 | Air-leakage rating, screen, operator |
| Electric or solar-powered venting skylight | High ceilings, owners who want rain sensors and remote control | Typical $2,000–$5,000+ | Rain sensor, motor warranty, wiring or solar panel location |
For a fuller breakdown of labor, roofing and interior finishing costs, see our skylight installation cost guide. If you have an existing skylight that is failing, our guide to skylight replacement explains when to replace the unit alone and when to replace flashing and curb too.
Fixed skylights
A fixed skylight does not open. With no moving sash and no operating seals, it is the simplest, least expensive and least leak-prone conventional skylight, and it typically posts the best air-leakage numbers. Deck-mounted units sit directly on the roof sheathing with a step-flashing kit around them and have a lower profile. Curb-mounted units sit on a raised wooden frame, which suits low-slope roofs and many older installations.
Venting skylights
Venting skylights open to release hot air and humidity, which helps in bathrooms, kitchens and upstairs rooms that trap summer heat. Manual units open with a crank or pole. Electric and solar-powered units use a remote or wall control, and most include a rain sensor that closes the sash automatically. Venting units cost more and add operating seals, a motor and controls that can eventually need service.
Tubular skylights
A tubular daylighting device uses a small dome on the roof, a highly reflective tube through the attic and a diffuser at the ceiling. It is far less disruptive to install than a conventional skylight, needs no light shaft framing, and moves daylight into interior spaces a conventional skylight cannot reach. It brings light, not a view. Our guide to the solar tube covers sizing, tube length and how much light to expect.
What Actually Matters When Choosing a Skylight
ENERGY STAR skylight criteria for Colorado
ENERGY STAR certifies skylights by climate zone using ratings certified by the National Fenestration Rating Council (NFRC). Skylights have their own criteria, separate from windows. A sloped or horizontal pane generally loses more heat on cold nights and gains more sun at midday than a vertical window of the same size, which is why a skylight deserves more attention to glass than its size suggests.
| Climate zone | U-factor | SHGC |
|---|---|---|
| Northern | 0.45 or lower | Any |
| North-Central, South-Central, Southern | 0.50 or lower | 0.25 or lower |
ENERGY STAR’s climate zone data places the Front Range counties, including Denver, Adams, Arapahoe, Jefferson, Douglas, Boulder, Broomfield, Larimer, Weld and El Paso, in the Northern zone, while a few southeastern Colorado counties fall in North-Central. That difference matters more for skylights than for windows or doors. In the Northern zone ENERGY STAR sets no SHGC limit, so a certified skylight may let in a lot of solar heat. In North-Central, SHGC must be 0.25 or lower. Check your ZIP code with the ENERGY STAR Climate Zone Finder before ordering.
“Any SHGC” does not mean any SHGC is a good idea in your room. ENERGY STAR’s Northern-zone criteria are tuned for heating-dominated climates, where winter sun is welcome. Front Range summers are sunny and intense at altitude, and a large skylight on a south- or west-facing slope can overheat a room on a July afternoon. Many owners choose a low-e glass option with a lower SHGC, add a blind or shade, or pick a venting unit that can dump heat.
U-factor and condensation
U-factor measures how much heat the whole unit loses; lower is better. A skylight is a hole in the warmest part of the house, so a low U-factor keeps the inner pane warmer in winter, which reduces condensation. Condensation on a skylight is often mistaken for a leak. It comes from warm, moist indoor air meeting cold glass or a cold, uninsulated light shaft. Insulating the shaft walls, sealing the shaft against attic air, and running bathroom fans help. Our guide to window condensation explains the same physics on vertical glass.
Glass vs acrylic or polycarbonate
Most quality skylights use insulated glass: two or three panes with a low-e coating and gas fill. A common configuration is a tempered outer pane, which is strong against impact, and a laminated inner pane, which holds together if broken so pieces do not fall into the room. Plastic domes in acrylic or polycarbonate are cheaper and lighter and are standard on tubular skylights, but older plastic domes on conventional skylights tend to yellow, craze and lose their seals, and they insulate poorly compared with insulated glass. In a hail region, read how the product’s glazing is rated for impact.
Hail and snow
The Front Range is one of the most hail-prone regions in the country. Tempered glass handles hail well, but the aluminum cladding, flashing and any plastic domes can dent or crack, and hail can damage the shingles around a skylight even when the glass survives. After a major storm, have the skylight and flashing checked along with the roof; our guide to hail damage to the roof explains what adjusters and roofers look for. Heavy wet spring snow loads the roof and can pile up against the uphill side of a skylight, so the flashing must handle meltwater and ice dams there.
Size, placement and slope
A skylight lets in far more light than a vertical window of the same size. Bigger is not better: an oversized skylight overheats and glares. Many manufacturers suggest the total skylight area in a room stay a small share of the floor area, typically no more than a few percent in rooms with plenty of windows and somewhat more in rooms with few. North-facing slopes give soft, even light with little heat; south- and west-facing slopes give more light and heat. Check the manufacturer’s minimum roof pitch for the unit and flashing kit, because low-slope roofs usually need a curb-mounted unit.
Blinds and shades
Room-darkening and light-filtering blinds made for the specific skylight model can be manual, electric or solar-powered. They help control summer heat and glare and are much easier to add at installation than later. In bedrooms, a blackout blind is close to essential.
Room-by-room choices
- Kitchens and family rooms. Fixed or venting units with a lower-SHGC glass option and a light-filtering blind. A venting skylight helps release cooking heat in summer.
- Bathrooms. A venting skylight or a tubular unit. A skylight is not a substitute for an exhaust fan, which codes generally still require where there is no operable window; good ventilation also limits condensation in the shaft.
- Bedrooms. Blackout blinds and careful placement away from the head of the bed; early summer sunrise comes through a skylight long before you want it.
- Hallways, closets and laundry rooms. Tubular skylights are usually the practical answer because they deliver light through long attic runs without framing a shaft.
- Vaulted ceilings. Conventional skylights install with short or no shafts, making them the most cost-effective here; electric venting units suit ceilings too high to reach.
A Buyer’s Checklist for Skylights
| Spec | What to look for | Why it matters |
|---|---|---|
| ENERGY STAR / NFRC | Certified for your zone: U-factor 0.45 or lower in Northern, plus air leakage 0.3 cfm/ft² or lower | Heat loss, condensation and drafts |
| SHGC | A lower-SHGC glass option on south and west slopes, even though Northern has no limit | Summer overheating at altitude |
| Glazing | Insulated glass with tempered outer and laminated inner pane; impact information for hail | Safety and durability |
| Type | Fixed, venting or tubular to suit light, ventilation and budget | Venting adds cost and moving parts |
| Flashing | Manufacturer’s flashing kit matched to roof material, plus self-adhered underlayment | Most skylight leaks are flashing failures |
| Mounting | Deck-mounted for most pitched roofs; curb-mounted for low slopes | Correct fit for the roof pitch |
| Light shaft | Insulated and air-sealed shaft walls, flared shaft for wider light spread | Prevents condensation and heat loss |
| Controls (venting) | Rain sensor, remote or wall control, motor warranty | Keeps an open skylight from letting storms in |
| Shades | Model-specific blind, blackout for bedrooms | Glare and summer heat |
| Warranty | Separate terms for glass, flashing, installation and motors; installer leak warranty | Leak coverage depends on who installed it |
Installation and the Home-Inspection Angle
The ASHI Standard of Practice requires home inspectors to inspect skylights along with flashing, chimneys and other roof penetrations, and skylights are one of the most common sources of roof-leak findings in inspection reports.
Flashing and water management
A skylight interrupts the roof’s water-shedding layers, so everything depends on how the installer rebuilds them. A good installation wraps the rough opening with self-adhered underlayment, uses the skylight manufacturer’s flashing kit designed for that unit and that roof material (shingle, tile or metal), and laps the head flashing under the shingles above and the sill flashing over the shingles below, with step flashing woven into each course on the sides. Roofing cement smeared around the edges in place of flashing is a red flag. Inspectors look for ceiling stains around the shaft, rusted or lifted flashing, missing step flashing, debris dams on the uphill side, and sealant-only repairs. Our guides to skylight leaks and roof flashing walk through what each looks like.
Timing with roof replacement
Skylight flashing is tied into the shingles around it, and an old skylight is rarely worth keeping through a new roof. Most roofers recommend replacing or at least reflashing skylights during a reroof, since doing it later means tearing into new shingles. If your roof is near the end of its life, plan the skylight and the roof together.
Structure
Installing a skylight between rafters or trusses is common. Wider units that require cutting a rafter or truss need headers and doubled framing, and trusses should not be cut without an engineer’s design. Inspectors look for cut framing without headers and sagging around the opening.
Safety glazing and fall hazards
Building codes have specific requirements for glass overhead because broken glass can fall into the room; the interior pane is typically laminated, or screens are required beneath other glass types. Skylights are also a fall hazard on the roof. OSHA’s construction fall-protection standard treats skylights as holes and requires workers to be protected from falling through skylights more than 6 feet above a lower level by covers, guardrails or personal fall arrest. Homeowners, holiday-light hangers and roofers alike should never step or lean on a skylight.
Electric skylights
Hard-wired venting skylights need a properly installed circuit and wiring made by a qualified electrician, and the control should be accessible. Solar-powered units avoid wiring but rely on a small panel and battery. Inspectors check that units open and close and that rain sensors work where reachable.
Evaluating an existing skylight when buying a home
Skylights in resale homes are often 20 to 30 years old. Signs that a unit is near the end of its life include a fogged or cloudy insulated glass unit (a failed seal), yellowed or crazed plastic domes, rust on the frame or flashing, water stains or peeling paint on the shaft walls, and a single-pane or plastic dome that drips condensation all winter. Ask the seller when the roof was last replaced and whether the skylights were replaced or reflashed at the same time. If the roof is new but the skylights are old, the flashing may have been reused, which is a common source of leaks after a reroof. A failing skylight is a reasonable item to price into negotiations, since replacement involves both roofing and interior work.
Maintenance
Skylights need little care, but a few habits extend their life. Clear leaves, pine needles and snow drifts from the uphill side, where debris dams can push water under the flashing. Clean the exterior glass from a ladder at the eave or with a long-handled tool rather than by walking on the roof. Check the ceiling around the shaft after heavy rain and after spring snowmelt. Test venting units and rain sensors each spring, and replace blind batteries or solar packs as needed.
Permits
Many Front Range cities and counties require a permit for a new skylight, because it involves cutting the roof deck and possibly framing, and some also require one for replacements or as part of a reroof permit. Check with your building department before work starts.
How to vet a skylight installer
- Roofing experience. The best skylight installers are roofers or skylight specialists who flash roof penetrations every day.
- License, insurance and permit. Confirm any required local license, liability and workers’ compensation coverage, and who pulls the permit.
- Manufacturer certification. Some skylight makers extend the leak warranty when a certified installer uses the matching flashing kit. Ask whether that applies.
- Written, itemized quote. It should name the exact model and size, glass option, flashing kit, underlayment, light-shaft framing, drywall, insulation and paint, electrical work, and debris removal.
- Leak warranty in writing. Ask how long the installer warrants against leaks, separate from the product warranty, and register the product warranty.
- Three quotes. A much cheaper bid often reuses old flashing or skips the underlayment.
Where to Buy a Skylight
Home-improvement retailers stock common fixed, venting and tubular skylights with matching flashing kits and blinds, and many offer installed-sales programs through local roofers. Roofing contractors and skylight dealers carry wider lines, larger sizes and certified installation. Get three quotes, ask each bidder which flashing kit and underlayment they will use, and coordinate with any planned reroof.
Where to shop for skylight
Links open the retailer's current selection — prices, stock and delivery/installation options vary by ZIP code.
We may earn a commission from qualifying purchases made through these links, at no extra cost to you.
Retailers and roofers carry brands such as Velux, Fakro, Solatube and ODL, among others. Compare the specific unit’s NFRC numbers, glazing, flashing kit and warranty terms rather than the brand name. If you are replacing glass elsewhere in the house, our sibling guide to the best patio door covers ENERGY STAR criteria for glass-heavy doors.
Frequently asked questions
What is the best type of skylight?
For most rooms, a fixed deck-mounted skylight with insulated low-e glass and the manufacturer's flashing kit is the simplest and least leak-prone choice. Choose a venting skylight where you need to release heat or moisture, and a tubular skylight for hallways, bathrooms and closets or when the attic is deep. Installation quality matters as much as the product.
What does ENERGY STAR require for a skylight in Colorado?
Most of Colorado, including the Front Range, is in ENERGY STAR's Northern zone, where a skylight needs a U-factor of 0.45 or lower with no SHGC limit. A few southeastern counties are North-Central, where U-factor must be 0.50 or lower and SHGC 0.25 or lower. Air leakage must be 0.3 cfm per square foot or less in all zones.
Do skylights always leak eventually?
No. Most leaks come from poor flashing, sealant-only installs, or old flashing reused during a reroof. A skylight installed with the manufacturer's flashing kit and self-adhered underlayment, and replaced or reflashed when the roof is replaced, can stay dry for decades. Condensation is often mistaken for a leak.
Is a solar tube better than a skylight?
A solar tube costs less, installs with less disruption, needs no framed light shaft and reaches interior spaces a conventional skylight cannot. A conventional skylight gives more light, a view of the sky and, if venting, ventilation. Choose by the room and by attic depth.
Can hail break a skylight?
Tempered glass skylights generally resist hail well, but plastic domes, aluminum cladding and flashing can crack or dent, and hail can damage the shingles around the unit. After a major hailstorm, have the skylights checked along with the rest of the roof.
Does a skylight increase home value?
A skylight can make a home more appealing by adding natural light, but it rarely returns its full cost at sale. Buyers and inspectors often look closely at skylights for leak history. A well-installed, dry skylight with documented work is an asset, while stains around it can raise concerns.
Why does my skylight have condensation on the inside?
Condensation on the inside of a skylight usually comes from warm, humid indoor air meeting a cold glass surface. Bathrooms and kitchens are common trouble spots. Running exhaust fans, lowering indoor humidity and choosing better insulated glazing help. Water between glass panes means a failed seal instead.
Should skylights be replaced with a new roof?
Yes, replacing or at least reflashing skylights during a new roof is usually recommended. Older skylights may not outlast the new roofing, and replacing them later means disturbing new shingles. Many roofers and manufacturers suggest new flashing kits as standard practice during a reroof.
More Questions About Skylights
How much does it cost to install a skylight?
Installing a skylight typically costs from several hundred dollars for a tubular skylight to several thousand dollars for a large venting unit with a new light shaft, according to industry estimates. Labor, roof type and interior finishing drive most of the price.
Costs climb when rafters must be cut and reframed, when the attic needs a drywall light shaft, or when the roof is tile, slate or steep. Electric or solar-powered venting units and blinds also add cost. Installing a skylight at the same time as a roof replacement usually saves on roofing labor and flashing work.
How long do skylights last?
A quality skylight commonly lasts around 15 to 25 years, though the flashing and seals often need attention sooner. Many skylights are replaced when the roof is replaced, so the flashing and unit start fresh together.
Signs a skylight is near the end include fogging between glass panes, cracked or yellowed acrylic domes, recurring leaks, and stuck or noisy venting mechanisms. Hail, ultraviolet exposure and freeze-thaw cycles all shorten life. Annual checks of the flashing and sealant, plus clearing debris around the curb, help a skylight reach the upper end of its expected life.
Do skylights make a room hot in summer?
Skylights can make a room noticeably hotter in summer, especially large, unshaded units on south- or west-facing roof slopes. Glass type, size and orientation matter more than the skylight style.
Ways to limit heat gain:
- Choose glazing with a low solar heat gain coefficient.
- Install interior or exterior shades.
- Prefer north-facing slopes for steady, cooler light.
- Use a venting unit to release hot air.
Tubular skylights bring in light with less heat gain because of their small opening.
Can you add a skylight to any roof?
Most pitched roofs can take a skylight, but rafter or truss spacing, roof pitch, roofing material and what sits in the attic can limit the size and location. Very low-slope or flat roofs usually need curb-mounted units designed for them.
Engineered trusses generally should not be cut without guidance from an engineer or the truss manufacturer, so smaller skylights that fit between trusses are common in newer homes. Ductwork, wiring and attic access also affect placement. Local building permits are often required, and a contractor or inspector can confirm whether the structure needs reinforcement.
References
- Residential Windows, Doors and Skylights: What Makes It ENERGY STAR — ENERGY STAR (U.S. EPA)
- ENERGY STAR Certification Criteria for Residential Skylights (October 2023) — ENERGY STAR (U.S. EPA)
- Windows, Doors, and Skylights Climate Zone Finder — ENERGY STAR (U.S. EPA)
- ASHI Standard of Practice for Home Inspection — American Society of Home Inspectors
- Duty to Have Fall Protection (29 CFR 1926.501) — Occupational Safety and Health Administration