SER Cable: Service Entrance Cable for Panels and Subpanels
Open the basement ceiling or the garage wall near an electrical panel in many homes and a thick gray cable often shows up, running from the meter to the main panel or from the main panel to a subpanel. That is frequently SER cable, a type of service entrance cable designed to carry large amounts of current. Because it handles a home’s main feed or a major branch of it, mistakes in sizing, termination or protection matter more than with ordinary branch wiring. This guide explains what SER cable is, how it differs from SEU, why aluminum is so common, where it is used, how it is sized, and what home inspectors and electricians look for. It is general information for homeowners and buyers on the Colorado Front Range; work on service and feeder conductors belongs with a licensed electrician and normally requires a permit.
Part of our Home Electrical guide — start there for the full picture →
What SER Cable Is
Service entrance cable is a broad category, often marked as type SE, intended for carrying power from the utility connection into a building and, in many cases, for feeders inside the building. Within that category there are styles. SER, short for “service entrance, round,” is the round style. It typically contains several individually insulated conductors plus a bare grounding conductor, all wrapped in a tough outer jacket.
A common SER configuration has four conductors: two insulated “hot” conductors, one insulated neutral, and one bare ground. Cable labels often describe this with a string of sizes, such as 2-2-2-4, which indicates three conductors of one size and a smaller grounding conductor. Three-conductor versions also exist for certain service applications.
That separate insulated neutral and separate ground is what makes SER so useful for feeding subpanels, where the neutral and the equipment ground must be kept apart.
SER Versus SEU Cable
The other common style is SEU, for “service entrance, unarmored.” It looks quite different:
- Shape. SEU is typically flat or oval. SER is round.
- Conductors. SEU usually has two insulated conductors with a bare conductor wrapped spirally around them as a concentric layer, which serves as the neutral. SER has separately insulated conductors and its own bare ground.
- Typical uses. SEU is often used on the service entrance itself, for example from the weatherhead down to the meter base and from the meter into the main panel. SER’s insulated neutral and separate ground make it the usual choice for four-wire feeders to subpanels, and it is also used on service entrances.
Because SEU has no separate insulated neutral, it is not generally suitable as a four-wire feeder to a subpanel. Seeing SEU feeding a subpanel, with the bare wrap used as both neutral and ground, is one of the things an electrician or inspector may question, though rules have changed over time and older installations may reflect earlier practices.
Aluminum Versus Copper SER Cable
SER cable is sold in both copper and aluminum, and aluminum is very common for large feeders and services. The reasons are practical: aluminum costs considerably less than copper for the same current-carrying job and weighs less, which matters on long runs of heavy cable.
Why modern aluminum is different
Many homeowners hear “aluminum wiring” and think of the problems associated with small-gauge aluminum branch-circuit wiring used in some homes built in the 1960s and 1970s. Those concerns centered on 15- and 20-amp circuits connected to outlets and switches that were not designed for aluminum. Our aluminum wiring guide covers that history.
Large-gauge aluminum service and feeder conductors are a somewhat different situation. Building wire made since the early 1980s is generally produced from AA-8000 series aluminum alloys, which were developed to address the creep and connection issues associated with older alloys. Large aluminum conductors have long been used by utilities and in residential services. They still require correct terminations, as described below, but large-gauge aluminum SER is widely accepted when installed properly.
Size and ampacity differences
Aluminum carries less current than copper of the same gauge, so aluminum SER for a given load is typically one or two sizes larger. A run that might use a certain copper size could need a larger aluminum size for the same rating. Electricians select the conductor from code ampacity tables based on material, insulation and temperature ratings.
Where SER Cable Is Used in a Home
Most residential uses fall into two groups.
Feeders to subpanels
The most common indoor use is feeding a subpanel from the main panel. Typical examples include subpanels for a finished basement, a garage or workshop, an addition, or a large kitchen. The four-conductor SER provides two hots, an insulated neutral and a ground. In the subpanel, the neutral and ground are normally kept on separate bars, with the neutral bar isolated from the enclosure, while the main service panel is where the neutral-to-ground bond is typically made.
Service entrance conductors
SER or SEU may also carry the service conductors between the utility connection point, the meter base and the main panel. On overhead services, the cable often runs down the exterior from the weatherhead, where drip loops keep water out, to the meter. On underground services, other conductor types are often used in conduit, and SER may appear inside the building between equipment.
Limits on where it goes
Service entrance cable has restrictions on routing, exposure to physical damage, and use in certain locations. Exterior runs where the cable could be struck, such as low on a garage wall near a driveway, are commonly protected or replaced with conduit. Runs inside a building may have limits on where service conductors can travel before reaching the main disconnect. These are code questions specific to the installation and jurisdiction.
How SER Cable Is Sized
Sizing SER is not a do-it-yourself calculation to guess at. The correct size depends on:
- The calculated load or the rating of the overcurrent device protecting the feeder.
- Conductor material, aluminum or copper.
- The insulation and terminal temperature ratings that apply.
- Where the cable runs, including through insulation or in hot attics.
- Run length, where voltage drop may justify upsizing.
- Any special rules for dwelling services and feeders that the adopted code allows.
Electricians take conductor sizes from the ampacity tables in the electrical code adopted by the jurisdiction. The breaker protecting a feeder must be matched to the conductor, never larger than the conductor’s allowed rating except where specific code exceptions apply. An undersized feeder on an oversized breaker is a classic overheating risk and one of the issues inspectors try to catch.
Because heat and sizing are so closely linked, a subpanel or service upgrade usually involves the whole chain: the main panel’s capacity, the main breaker, the feeder breaker and the cable. Our electrical panel upgrade guide covers the broader project.
Terminations, Anti-Oxidant and Torque
Most problems with large conductors show up at the connections rather than along the cable. A loose lug can heat, oxidize and degrade over time.
- Rated lugs. Lugs and terminals must be rated for the conductor material. Most modern panel lugs are marked for aluminum and copper (often “AL/CU”). The bus bar and its lugs are where feeder conductors land in many panels.
- Anti-oxidant compound. Aluminum forms an oxide layer quickly. Many electricians wire-brush and apply an anti-oxidant compound to aluminum conductors before inserting them into lugs. Some manufacturers specify or recommend it; others consider it optional for their lugs. Following the equipment instructions is the safe practice.
- Torque. Lug screws should be tightened to the torque value marked on the equipment or in its instructions, typically with a torque tool. Over- or under-tightening can both cause problems.
- Stripping. Conductor strands should be fully seated without nicks. Cut strands reduce capacity and can create hot spots.
Signs of trouble at terminations, which an electrician may find on thermal scans or visual checks, include discoloration, melted insulation, and a burnt or pitted appearance on lugs. CPSC electrical-safety guidance lists warning signs such as dimming or flickering lights, buzzing or sizzling sounds, the odor of overheated plastic and hot switch plates, and recommends having a licensed electrician check the home’s electrical system when they appear.
Sheath Damage, Support and Protection
The outer jacket of SER cable protects the conductors from abrasion, moisture and sunlight in rated applications. Damage to that jacket is one of the more common observations in older homes.
- Exterior jacket degradation. Older service entrance cable on south- and west-facing walls can become cracked, brittle or split after decades of sun. Colorado’s strong high-altitude sun can speed that weathering.
- Physical damage. Nicks from tools, crushed sections where cable was stapled too tightly, or damage near driveways and lawn equipment.
- Support. Cable should be secured with appropriate straps at intervals and near boxes and panels, and it should not hang loosely across a basement or garage. Specific spacing comes from code and the cable manufacturer.
- Entry fittings. Where SER enters a panel, a proper connector or clamp should secure it and protect the cable from the sharp edges of the knockout.
- Bending radius. Very sharp bends can stress insulation on large conductors.
Water intrusion is another issue on exterior service cable. Water can track down cable jackets into the meter base or panel if drip loops or weathertight fittings are missing.
Grounding and Bonding Around SER
The bare conductor in a four-wire SER feeder is an equipment grounding conductor, not a neutral. At the main service, the grounding electrode system, often including a ground rod and connections to metal water piping where present, connects to the service equipment. Bonding the neutral to ground typically happens at that service point only. A subpanel with neutral and ground bonded together is a common observation; it can create unwanted current paths on metal parts and grounding conductors.
Grounding rules are detailed and have changed over the years, so a professional should evaluate any questions about whether a given installation is correct for its age and jurisdiction.
What Home Inspectors Check
The ASHI Standard of Practice directs inspectors to inspect the service drop, service entrance conductors, cables and raceways, service equipment and main disconnects, service grounding, interior components of service panels and subpanels, conductors, and overcurrent protection devices. Inspectors are also asked to describe the service amperage rating and the location of main disconnects and subpanels. The same standard states that inspectors are not required to measure amperage, voltage or impedance.
In practice, around SER cable an inspector may note:
- Damaged, weathered or unsupported exterior service cable.
- Missing drip loops or weathertight fittings.
- Feeder conductors that appear small for the breaker protecting them.
- Aluminum conductors without signs of proper termination, or with visible discoloration.
- Bonded neutrals and grounds in subpanels.
- Missing cable clamps at panel entries.
These findings normally lead to a recommendation for evaluation by a licensed electrician rather than a conclusion about compliance.
Electrical Fire Risk and Safety
The U.S. Fire Administration reports that in 2021 an estimated 24,200 residential building electrical fires were reported to fire departments in the United States, causing an estimated 295 deaths, 900 injuries and over $1.2 billion in property loss. Service and feeder conductors are only one part of that picture, but heat at large connections is a real hazard.
Work on service conductors is also dangerous because the conductors ahead of the main breaker remain energized even with the main off. OSHA’s electrical safety materials, written for workers, describe electricity as a long-recognized serious workplace hazard that exposes people to electric shock, electrocution, fires and explosions. That is a strong reason homeowners should leave service-side work to licensed electricians and the utility.
Reusing or Replacing SER During an Upgrade
When a home gets a new main panel, a larger service or an added subpanel, the existing SER cable is one of the first things an electrician evaluates. Reusing it can save money, but only when it is still suitable for the new job.
Factors that commonly decide the question:
- Size versus the new rating. A feeder that was correctly sized for a 60-amp subpanel may be too small if the new subpanel and breaker are larger. Upsizing the breaker without upsizing the cable is not an acceptable shortcut.
- Number of conductors. Older three-wire feeders without a separate ground may not meet current rules for a new subpanel, which usually calls for a four-wire feeder.
- Jacket and conductor condition. Brittle, cracked or heat-discolored cable is typically replaced rather than reconnected.
- Length at the new panel location. If the panel moves, the old cable may no longer reach. Splicing large conductors is possible with listed connectors in approved enclosures, but many electricians prefer a continuous new run where practical.
- Utility requirements. On the service side, the utility may set its own rules for meter equipment and service conductors.
For buyers, an inspection report that mentions an older feeder, a crowded panel or an added subpanel is a good prompt to ask an electrician about the feeder’s size and condition before planning projects such as an EV charger, a hot tub or a basement finish.
SER Cable Costs
Cable prices move with metal markets, so the numbers below are rough 2026 planning ranges.
- Aluminum SER. Often a few dollars per foot for common feeder sizes, more for larger sizes.
- Copper SER. Usually several times the price of comparable aluminum, sometimes more.
- Subpanel feeder run. Installing a subpanel with a short to moderate SER feeder commonly runs from several hundred to a few thousand dollars depending on distance, access, and panel and permit costs.
- Service entrance cable replacement. Replacing weathered exterior service cable, with utility coordination, often runs several hundred to a couple thousand dollars.
- Larger projects. When SER is part of a broader update, see house rewiring cost for wider ranges.
Hiring an Electrician for SER Work
Feeder and service conductor work typically requires a licensed electrician, a permit and an inspection in Colorado jurisdictions, and service-side work often requires utility coordination. Our hiring process overview explains how to vet contractors, and the electrical section covers questions specific to electricians, such as license verification, permit handling and how load calculations are done.
More Questions About SER Cable
Can SER cable be buried underground?
No, standard SER cable is not rated for direct burial. Its jacket is not designed for continuous soil moisture or wet locations underground, so buried feeders typically use conductors rated for wet locations, such as USE-2 or XHHW-2, often in conduit, or cable specifically listed for direct burial.
Running SER into a conduit underground does not solve the problem, because underground conduit is considered a wet location. A feeder to a detached garage or shop usually needs a different cable type for the buried section. An electrician can choose conductors that meet local code.
Can SER cable feed a range or dryer circuit?
SER cable can be used for some branch circuits, such as an electric range, when the installation meets the electrical code’s requirements for size, termination and grounding. It is more commonly used for subpanel feeders, but some electricians use it for large 240-volt appliance circuits.
Ranges and dryers installed today require four-wire circuits with a separate equipment ground, which four-conductor SER provides. Older three-wire range circuits are a different matter and are generally only allowed to remain on existing installations. A licensed electrician should confirm size and terminations.
Can SER cable be run in conduit?
SER cable can be run in conduit for short sections where physical protection is needed, such as through a garage wall or up an exterior wall, but running long stretches of cable inside conduit is less common because it is bulky and can require derating.
When a feeder needs conduit for its full length, electricians usually pull individual conductors such as THHN/THWN instead, which are easier to install and size. Conduit fill and heat limits still apply. Sleeves where SER passes through masonry or exposed areas are a common, accepted use.
How do you recognize old cloth-jacketed service entrance cable?
Old service entrance cable from decades past often has a woven fabric or tar-impregnated cloth jacket, typically dark gray or black, rather than the smooth gray plastic jacket on modern cable. On a house exterior it may look cracked, frayed or shredded where sunlight and weather have worn it.
Deteriorated jackets let water follow the cable into the meter base or panel, which can corrode connections. Home inspectors commonly flag worn service entrance cable for evaluation by an electrician. Replacement often requires coordination with the electric utility for the service drop.
How far can SER cable run before voltage drop matters?
SER cable runs of more than about 100 feet often deserve a voltage drop calculation, because longer runs can cause noticeable voltage loss under heavy load. Many designers aim to keep feeder voltage drop around 2 to 3 percent, a common recommendation rather than a strict code requirement.
Long runs to a detached garage, shop or addition may need a larger cable size than ampacity alone requires. Aluminum conductors have more resistance than copper of the same size, so they are upsized more often. An electrician can run the calculation for the actual load and distance.
References
- Appliance and Electrical Fire Safety — U.S. Fire Administration
- Electrical Safety — U.S. Consumer Product Safety Commission
- Electrical Safety and Health Topics — Occupational Safety and Health Administration
- ASHI Standard of Practice for Home Inspection — American Society of Home Inspectors
Frequently asked questions
What is SER cable used for?
SER cable is a round service entrance cable commonly used for feeders from a main panel to a subpanel and for some service entrance runs. Its separate insulated neutral and bare ground suit four-wire feeders.
What is the difference between SER and SEU cable?
SER is round with separately insulated conductors and a bare ground. SEU is usually flat with two insulated conductors and a concentric bare neutral, and it is typically used on service entrances rather than subpanel feeders.
Is aluminum SER cable safe?
Large-gauge aluminum SER made from modern AA-8000 series alloys is widely used when terminated correctly in lugs rated for aluminum. Its concerns differ from older small-gauge aluminum branch wiring.
What size SER cable is needed for a 100-amp subpanel?
It depends on conductor material, insulation and terminal ratings, run conditions and the adopted code tables. A licensed electrician should size the feeder and match the breaker.
Can a homeowner install SER cable?
Some jurisdictions allow homeowner permits for limited work, but feeder and service conductor work carries serious shock and fire risk. Hiring a licensed electrician with a permit is the usual path.
What do the numbers on SER cable mean?
Numbers on SER cable, such as 2-2-2-4, describe conductor sizes in AWG: typically two hots and a neutral of one size and a smaller ground. The jacket also shows conductor material, voltage rating and listing. Read the full print legend, not just the size, before buying.
Is SER cable rated for outdoor use?
Many SER cables are rated for sunlight resistance and can run on exterior walls, but the jacket marking must show it. SER is not intended for wet locations such as underground. Exterior runs need proper supports, weather-tight fittings and drip loops at the meter and panel.
Can SER cable be spliced?
SER cable can be spliced when needed, using listed connectors inside an accessible, appropriately sized junction box. Splices hidden inside walls without a box are not allowed. Because SER carries feeder-level current, splices should be torqued to specification and done by a licensed electrician.
How tight can SER cable be bent?
SER cable has a minimum bending radius, commonly cited as about five times the cable's diameter for service entrance cable. Bending tighter can damage insulation and the cable jacket. Plan routes with gentle bends, especially in tight panel enclosures and around framing corners.
Curious about the service cable, panel and subpanels in a home you are considering on the Front Range? Contact us and we will connect you with a vetted local inspector.