Skip to content
Independent home-inspection guidance. We are not affiliated with the prior occupant of this domain.
Find an inspector

House Rewiring Cost: When It’s Needed and What to Expect

By InspectandTest Editorial Team Published October 3, 2026 Updated November 13, 2026

We may earn commission from links on this page. Lead-form submissions are forwarded to local inspector partners. How we research and review.

Photo via Unsplash by Artful Homes

Rewiring is one of those projects most homeowners never plan for until an inspection report, an insurance renewal or a flickering light forces the question. Older Front Range houses, from Denver bungalows and Englewood ranches to 1960s and 1970s tract homes in Aurora, Lakewood and Colorado Springs, can carry original wiring that was never designed for today’s electrical loads. The price to rewire a house varies more than most home projects because so much depends on what is behind the walls, how easy it is to reach and how much patching follows. This guide covers the conditions that typically trigger a rewire, the difference between partial and full rewiring, rough cost ranges, the factors that push bids up or down and how the permit and inspection process works. All cost figures are general industry estimates, not quotes, and electrical work of this scope belongs to a licensed electrician.

Electrical problem? Talk to a licensed electrician.

📞 Call (877) 560-2714

Free, no-obligation quote · Connect with a local pro. Calls may connect you with a partner contractor; we may be compensated for calls.

What Is the Price to Rewire a House?

As a broad industry estimate, a full rewire of a typical single-family home often lands somewhere around $4 to $10 per square foot, with easy-access homes at the low end and plastered, finished, multi-story homes at the high end. For a 1,500 square foot house, that rough range works out to about $6,000 to $15,000. Larger homes, difficult access, a required panel upgrade and extensive wall repair can push totals above $20,000 or $30,000.

Partial rewiring, such as replacing a handful of ungrounded circuits, rewiring a kitchen or remediating one problem area, frequently costs a few thousand dollars. A single new dedicated circuit is usually a few hundred dollars to over a thousand depending on distance and access.

These figures move with labor rates, permit fees, copper prices and the condition of the house. The only reliable number is a written bid from a licensed electrician who has looked in the attic, the basement and the panel.

Rough Cost Ranges by Home Size

Home size Full rewire, accessible (rough) Full rewire, plaster or finished (rough)
1,000 sq ft $4,000 – $7,000 $7,000 – $12,000
1,500 sq ft $6,000 – $10,000 $10,000 – $16,000
2,000 sq ft $8,000 – $13,000 $13,000 – $22,000
3,000 sq ft $12,000 – $20,000 $20,000 – $32,000+

Ranges exclude major wall finishing, painting and large panel or service upgrades unless noted in a bid. Treat them as a planning tool, not a budget.

When Does a House Need Rewiring?

Most homes never need a complete rewire. Modern copper wiring in good condition can last for many decades. The question usually comes up because of the wiring type, its condition or its capacity.

Knob-and-Tube Wiring

Homes built before roughly the 1940s may still have knob-and-tube wiring: individual conductors on ceramic knobs and through ceramic tubes, with no ground conductor. The original insulation can become brittle, the system was not designed for buried insulation in walls and attics, and decades of amateur splices are common. Many insurers ask about knob-and-tube, and some will not write a policy until it is replaced. Our guide to knob-and-tube wiring covers how to identify it and what inspectors look for.

Aluminum Branch Circuit Wiring

From the mid-1960s to the mid-1970s, some homes were wired with aluminum on general-purpose 15 and 20 amp circuits. The U.S. Consumer Product Safety Commission’s publication on repairing aluminum wiring reports that failing connections can overheat at receptacles, switches and splices, and that warning signs are often hard to detect. Aluminum wiring does not automatically mean a full rewire. CPSC’s publication lists three permanent repair methods: complete replacement with copper cable, the COPALUM crimp repair method and the AlumiConn connector as an acceptable alternative. Each has trade-offs in cost, availability of trained installers and wall access, and an electrician can explain which suits a specific house. See our aluminum wiring guide for more detail.

Ungrounded Two-Prong Circuits

Many homes from the 1950s and early 1960s use two-wire cable without a ground. These circuits are not necessarily dangerous, but they limit what can be safely plugged in and do not provide a ground path for surge protection. Options range from adding GFCI protection, to running new grounded circuits to key rooms, to a full rewire.

Damage, Overloading and DIY Work

Signs that wiring may need repair or replacement include scorched or discolored outlets, a burning smell, frequent breaker trips, warm cover plates, flickering lights, rodent-chewed cable in the attic and extension cords used as permanent wiring. Undersized wire on a breaker that is too large is a fire hazard and is a frequent inspection finding where previous owners added circuits themselves.

The stakes are real. According to NFPA’s research on home electrical fires, local fire departments responded to an estimated annual average of 46,652 home structure fires involving electrical failure or malfunction or electrical distribution, lighting or power transfer equipment from 2020 to 2024. Not every one of those relates to wiring age, but the figure is a reminder that wiring problems deserve professional attention.

Insurance and Sale Pressure

Insurance companies, lenders and buyers’ agents sometimes push the issue. A carrier may raise premiums, require an electrician’s letter or decline coverage for homes with knob-and-tube, aluminum branch wiring or certain panels. Sellers in competitive Front Range markets have found that a documented update can remove a negotiating point.

Partial vs. Full Rewiring

A full rewire replaces essentially all branch circuit wiring in the home, often along with the panel, receptacles, switches and some fixtures. A partial rewire targets specific problems: a kitchen remodel, ungrounded bedroom circuits, an aluminum-wired addition or a few runs of damaged cable.

Factor Partial rewire Full rewire
Typical scope Selected rooms or circuits Entire home’s branch wiring
Cost (rough) Hundreds to a few thousand dollars Often five figures
Disruption Days, localized One to several weeks, house-wide
Insurance effect May not satisfy a carrier asking about knob-and-tube Usually resolves wiring-type questions
Good fit for Mixed-age homes with limited problem areas Homes with widespread obsolete or damaged wiring

Partial work makes sense when the problem is truly limited. It becomes less economical when an electrician keeps finding the same old wiring in every wall, because mobilization, permits and patching costs repeat each time. Timing also matters. If walls are already open for a remodel, rewiring those areas costs far less than it would later.

What Drives the Cost of Rewiring

Two houses of the same size can produce bids thousands of dollars apart. The main variables are below.

Access

A single-story ranch with an open attic and unfinished basement is the easiest case. Electricians can drop wires down from above and feed them up from below with minimal wall openings. Finished basements, two-story homes with no attic above the first floor, cathedral ceilings and slab foundations all require more fishing, more holes and more labor hours.

Plaster and Lath Walls

Older homes with plaster walls are slower to work in. Plaster cracks easily, lath obstructs fishing tools and openings are harder to patch invisibly. Some homeowners accept surface-mounted raceway in a few places to limit wall damage. Others prefer to bundle rewiring with a remodel when walls are already open.

Panel and Service Upgrade

A rewire is often the right moment to replace an old or undersized panel. A new panel or a move from 100 to 200 amp service can add a few thousand dollars, depending on whether the meter base and service entrance cable also need work. Our guide to electrical panel upgrades explains the signs, the utility steps and typical ranges. A rewire is also a natural time to consider a whole-house surge protector.

Code Upgrades

New wiring generally must meet the code edition currently adopted by the local jurisdiction. That can mean AFCI and GFCI protection in more locations, tamper-resistant receptacles, more kitchen and bathroom circuits and updated smoke and carbon monoxide alarm wiring. These features add device cost but are part of what a rewire buys.

Permits and Inspections

Electrical permits for a rewire are normally pulled by the licensed electrician, and fees vary by city and county. Expect a rough-in inspection while walls are open and a final inspection when the work is complete.

Wall and Ceiling Repair

Many electrical bids exclude finish repairs. Patching, texture matching and painting can add a meaningful amount, especially in plaster homes or where textured ceilings must be matched. Ask each bidder exactly who is responsible for patching and to what level of finish.

Other Variables

  • Number of circuits, outlets, switches and fixtures.
  • Hazardous materials. Pre-1980 homes may have asbestos in some textures, insulation or old wiring materials and lead in paint, which may require testing before walls are disturbed.
  • Local labor rates and how busy electricians are in a given season.
  • Copper and equipment prices, which fluctuate.

Living in the Home During a Rewire

Many families stay in the house during a rewire, especially a phased one. Electricians often work room by room or circuit by circuit so that most of the house has power at the end of each day. Expect some days with power off for several hours, dust, furniture moved away from walls and workers in the attic and crawl space.

Practical steps help. Clear a path to the panel, attic hatch and crawl space. Protect floors and electronics. Agree on a daily schedule for power shutdowns, and plan around home offices, medical equipment, refrigerators and freezers. In winter, ask how furnace power and heat tape will be handled, since a cold Front Range night is not a good time to lose the blower. Households with infants, respiratory conditions or older plaster that may contain hazardous materials sometimes choose to stay elsewhere for the noisiest days.

Timelines vary. A partial job may take one to three days. A full rewire of an occupied home commonly takes one to several weeks, plus scheduling time for inspections and wall repair.

Ways to Manage the Cost

A rewire is rarely cheap, but there are legitimate ways to keep the number reasonable without cutting corners on safety.

  • Coordinate with other projects. If a kitchen remodel, basement finish, insulation job or drywall replacement is already planned, rewire those areas while the framing is exposed. Labor for fishing wire through closed walls is often the largest single line item.
  • Phase the work by priority. Electricians can address the most hazardous circuits first, such as overheated connections, damaged cable or bedroom circuits on brittle insulation, and schedule lower-risk areas later. Each phase carries its own permit and mobilization cost, so phasing trades some efficiency for cash flow.
  • Clear access yourself. Emptying closets, moving furniture, clearing attic storage and opening a path in the crawl space saves billable hours.
  • Handle cosmetic finishing separately. Some owners hire the electrician for wiring and rough patching, then hire a painter or drywall finisher for final texture and paint. Confirm the plan in writing so nothing falls between trades.
  • Ask about surface raceway in limited spots. In plaster homes, a short run of surface-mounted raceway in a closet or utility area can avoid a large opening in a finished wall.
  • Check for incentives. Some utilities and local programs offer rebates tied to electrification projects, such as heat pumps or induction ranges, that may help offset a related panel or service upgrade. Programs change often, so verify current terms.

What not to do is equally clear. Unpermitted rewiring, mixing new and old wiring without proper connections and hiring unlicensed help to save money tend to create problems that surface at the next sale, the next insurance inspection or, worse, as a fire.

Rewiring Before or After You Buy

For buyers, wiring findings often arrive during the inspection window, when time is short. A general inspection may note the wiring type, but a buyer facing knob-and-tube, aluminum branch wiring or widespread ungrounded circuits usually benefits from an electrician’s evaluation and a written estimate before the objection deadline. That estimate turns an open-ended worry into a number that can support a price reduction, a seller credit or a repair request.

Seller-completed repairs deserve scrutiny. Ask for the permit number, the electrician’s license information and the final inspection sign-off, and confirm the scope matches what was promised. A credit at closing gives the buyer control over who does the work and how, which some buyers prefer for a project this large. Others would rather move in with the work finished. Either path is reasonable when it is documented.

Current owners planning to sell in a few years face a different calculation. Rewiring is rarely recovered dollar for dollar in sale price, but obsolete wiring can shrink the buyer pool, complicate insurance for the next owner and slow a transaction. Getting an electrician’s assessment well before listing leaves time to decide calmly.

Inspection, Documentation and Hiring

For buyers, the first step is usually a home inspection. Under the American Society of Home Inspectors (ASHI) Standard of Practice, inspectors describe the predominant branch circuit wiring method, with knob and tube listed in the standard’s definitions as one example of a wiring method, and inspect a representative number of receptacles, switches and fixtures. An inspection does not open walls or evaluate every circuit, so a finding like “knob-and-tube observed in attic” or “aluminum branch wiring present” is a signal to bring in an electrician for a full evaluation. Our electrical inspection guide explains how a dedicated electrical evaluation differs from a general home inspection, and our guide to hiring a home inspector covers choosing the right professional.

NFPA’s home electrical safety tips recommend having all electrical work done by a qualified electrician and, when buying or remodeling, having the home inspected by a qualified private inspector or according to local requirements.

Questions to Ask Electricians

  1. Is the bid for a partial or full rewire, and exactly which circuits are included?
  2. Does it include a new panel, service upgrade, grounding and bonding?
  3. Who pulls the permit, and are permit fees included?
  4. How many wall openings do you expect, and who patches and paints them?
  5. Will old wiring be abandoned in place, disconnected or removed?
  6. What is the daily schedule for power outages?
  7. How long is the workmanship warranty?

Get at least two or three written bids. When bids differ widely, the reason is usually scope, not price gouging, so compare line by line. Keep permit records, inspection sign-offs and the electrician’s invoice; insurers and future buyers often ask for them.

More Questions About House Rewiring

Can a house be rewired without removing drywall?

Yes, most houses can be rewired without removing whole walls; electricians usually fish new cable through small access holes cut at outlets, switches, and top or bottom plates.

Access from an open attic, unfinished basement, or crawl space makes this much easier and reduces patching. Some holes are still needed where wires must cross framing, and plaster-and-lath walls take more care than drywall. Expect a number of small openings that a drywall or plaster contractor patches and paints afterward. Full wall removal is usually only necessary during a major renovation when walls are already being opened.

Is it worth rewiring an old house before selling?

Rewiring an old house before selling is worth it mainly when the existing wiring blocks financing or insurance, such as knob-and-tube or significant safety defects.

Buyers’ lenders and insurers sometimes refuse homes with outdated wiring, which shrinks the buyer pool. In those cases, rewiring or at least correcting the most problematic circuits may help the sale. Otherwise, pricing the home to reflect the wiring and disclosing it may be more cost-effective than a full rewire. An electrician’s written evaluation helps sellers and buyers judge the actual risk.

Is it safe to buy a house with knob and tube wiring?

Buying a house with knob-and-tube wiring can be done safely if the wiring is evaluated by a licensed electrician and a plan for replacement or repair is in place.

Knob-and-tube wiring lacks a ground conductor, was not designed for modern electrical loads, and is often found modified or buried under insulation, which raises fire concerns. Many insurers limit or decline coverage on homes that still have active knob-and-tube circuits. Getting an insurance quote and an electrician’s estimate during the inspection period helps buyers negotiate a credit or price reduction.

Does rewiring a house increase its value?

Rewiring a house rarely adds dollar-for-dollar resale value, but it can protect value by removing a major objection for buyers, lenders, and insurers.

Updated wiring and a modern panel improve safety, allow added circuits for kitchens, electric vehicles, or heat pumps, and reduce insurance problems. Appraisals typically do not credit wiring as heavily as visible upgrades like kitchens. Keeping permits, inspection sign-offs, and the electrician’s invoice gives future buyers proof of the work, which helps the home stand out in a sale.

References

Frequently asked questions

How much does it cost to rewire a house?

As a rough industry estimate, a full rewire often runs about $4 to $10 per square foot, or roughly $6,000 to $15,000 for a 1,500 square foot home. Plaster walls, difficult access, panel upgrades and wall repair can push the total higher. Get written bids from licensed electricians.

Can I live in my house while it is being rewired?

Often, yes. Electricians commonly work room by room so most of the house has power at night, though expect daytime outages, dust and moved furniture. Some households stay elsewhere for the most disruptive days.

Does aluminum wiring mean I need a full rewire?

Not necessarily. CPSC's guidance lists complete replacement with copper, the COPALUM crimp method and the AlumiConn connector as permanent repair options. An electrician can recommend which is practical for your home and budget.

How long does it take to rewire a house?

A partial rewire may take one to three days. A full rewire of an occupied home commonly takes one to several weeks, plus time for permit inspections and wall patching.

Will insurance cover rewiring?

Standard homeowners policies generally do not pay for upgrading old wiring. However, some insurers require replacement of knob-and-tube or other older wiring before issuing or renewing a policy, so check with your carrier.

Does rewiring a house require a permit?

Yes, rewiring a house almost always requires an electrical permit and inspections. Permits protect the homeowner by making sure work meets code, and unpermitted work can cause problems with insurance claims, appraisals, and future sales.

Can I rewire a house myself?

Some jurisdictions allow homeowners to pull permits and do their own electrical work, but full rewiring is complex and risky. Most homeowners hire a licensed electrician, and insurers or buyers may question unpermitted DIY wiring.

Do I need a new electrical panel when rewiring a house?

Many rewiring projects include a new panel, especially if the existing one is undersized, outdated, or a model with known safety concerns. An electrician can confirm whether the panel and service capacity fit the home's current and planned loads.

Shopping for an older Front Range home and unsure what is behind the walls? Contact us to be connected with a vetted local inspector who can flag wiring concerns before you commit.