Stair Landings: Size, Placement, and Safety Basics
Most people think of a staircase as a single run of steps, but many stairs include a flat platform somewhere along the way. That platform is a landing. It gives people a place to stop, turn, open a door or catch their balance, and it breaks a tall climb into shorter, safer flights. Landings are easy to overlook because they are usually simple: a level floor area at the top, bottom or middle of a stair. Yet they are tied to several of the rules that govern stair safety, and a landing that is too small, out of level, poorly supported or missing entirely is a common note in home inspection reports. Front Range homes have plenty of them, from split-level entries in Denver suburbs to basement stairs, back-door stoops and multi-level decks built on sloped lots in the foothills. This guide explains what a landing is, where landings are typically expected, general size guidelines, exterior and deck landings, handrail continuity, common defects and repair costs.
Part of our Structure & Exterior guide — start there for the full picture →
What a Stair Landing Is
A landing is a level platform at the end of a flight of stairs or between two flights. It differs from a tread because it is deeper than a single step and is designed for people to stand on, turn on or pause on, rather than simply step across.
Landings generally fall into a few types:
- Top and bottom landings: The floor area at the head and foot of a stair. In many homes this is simply the hallway or room floor, but it still has to provide enough clear space to step on and off the stair safely.
- Intermediate landings: A platform partway up a stair that breaks one tall flight into two shorter ones. These are common in homes with high ceilings and in long basement stairs.
- Turning landings: A platform where the stair changes direction, usually by 90 degrees (an L-shaped stair) or 180 degrees (a U-shaped or switchback stair).
- Door landings: The level area on each side of an exterior door, such as a back-door stoop or the platform at the top of a deck stair.
A turning landing is one of two common ways to change a stair’s direction. The other is a set of wedge-shaped treads that turn the corner without a flat platform. Those are covered in our guide to winder stairs, and the trade-offs between the two approaches are discussed later in this article.
Where Landings Are Typically Required
Residential building codes in the United States generally call for landings in several situations. The exact wording, dimensions and exceptions depend on the code edition a city or county has adopted and any local amendments, so the points below are general descriptions, not code text. The local building department is the authority on what applies to a specific house.
At the Top and Bottom of Stairs
Codes commonly expect a landing or floor area at the top and bottom of each stair. The idea is straightforward: people need somewhere level to stand before taking the first step down or after taking the last step. A stair that ends directly against a wall, a door that swings over the top step, or a bottom step that drops onto a sloped walk all raise safety concerns.
At Doors
Doors generally need a level landing on each side, especially exterior doors. Stepping out of a door straight onto a stair, or having a door swing out over a step, makes it easy to lose balance. Many codes include limited exceptions for certain doors, such as allowing a small step down at some exterior doors or allowing a stair at the inside of a door if the door does not swing over it. The details vary, which is why this is one of the more common questions for local code officials.
To Limit the Height of a Single Flight
Codes typically limit how tall a single flight of stairs can be before a landing is needed. In general terms, a long, uninterrupted climb is broken up with an intermediate landing. This matters in homes with tall ceilings, multistory entries and some basement stairs, as well as on decks that sit well above grade.
Typical Landing Dimensions
Size guidelines for landings are usually written in relation to the stair they serve. As a general rule of thumb, a landing is expected to be at least as wide as the stair and to have a depth, measured in the direction of travel, roughly equal to the stair width, with some codes setting a minimum depth regardless of how narrow the stair is. Turning landings need enough room for a person to make the turn without stepping off the edge or brushing a wall.
Other common expectations include:
- Level surface: Landings are meant to be essentially flat, though exterior landings are often allowed a slight slope for drainage.
- Clear area: Door swings, furniture, storage and appliances should not reduce the usable space. A door swinging over a landing may be allowed in some cases if it does not cut the landing below a minimum clear depth.
- Headroom: The ceiling or framing over a landing needs to allow adequate clearance, just like the stair itself.
- Consistent first and last steps: The step from the landing onto the stair should match the other risers. A taller or shorter step at the landing is a common trip hazard.
Because exact numbers differ between code editions and jurisdictions, any new construction, remodel or significant repair should be checked against the locally adopted code before work begins.
| Landing location | General expectation | Common problems found |
|---|---|---|
| Top of interior stair | Level floor area at least as wide as the stair | Door swinging over the top step, cramped hallway |
| Bottom of interior stair | Clear, level area to step off safely | Last riser taller or shorter than the rest, clutter, rugs |
| Intermediate or turning landing | Depth roughly equal to stair width, level and well supported | Undersized platform, sagging framing, loose handrail at the turn |
| Exterior door landing | Level platform outside the door, slight drainage slope allowed | Door opening onto a step, settled stoop, ice buildup |
| Deck stair landing | Firm, level surface at the bottom and at any turn | Stairs ending on soil or loose pavers, missing footings |
Exterior Landings at Doors and Decks
Exterior landings face weather, settling soils and heavy use, so they tend to show more defects than interior ones.
Stoops and Door Landings
A concrete stoop at a front or back door is a type of landing. Over time, stoops can settle or tilt toward the house, crack, or pull away from the foundation, which can leave the door threshold sitting higher than the landing. That creates a step-down right at the door, often in a spot where people are carrying groceries or watching a pet rather than their feet. A stoop that slopes toward the house also directs water toward the foundation and the door sill.
Deck Stair Landings
Decks frequently have landings at the top where the stair leaves the deck, at the bottom where it meets the ground, and partway down if the deck is high. Problems include bottom landings that are just soil or loose pavers, intermediate platforms framed without adequate support, and stairs that turn on a landing too small for the stair width. Our guide to deck stairs covers stringer attachment, rise and run, and footing issues in more detail.
Snow and Ice on the Front Range
Colorado’s Front Range sees repeated freeze-thaw cycles and heavy spring snow. Exterior landings collect snow, and meltwater that runs off roofs and freezes overnight can leave a sheet of ice exactly where people step out of the door. Gutters that overflow above an entry, downspouts that discharge onto a stoop and landings that slope the wrong way make this worse. Covered entries, good drainage, textured surfaces and exterior lighting all help, as does keeping a landing clear rather than letting snow pack down.
Handrails and Guards at Landings
Landings are where handrail problems often show up. A handrail that stops at the landing and starts again on the next flight forces people to let go and reach for a new rail, often at the exact moment they are turning. Codes typically require a handrail on at least one side of a stair with a certain number of risers, and in many cases the handrail is expected to be continuous along the flight, though interruptions are sometimes allowed at landings. Even where a break is permitted, a rail that continues around the turn is generally easier and safer to use.
Points worth checking at landings include:
- Handrail continuity: Whether the rail runs smoothly from one flight to the next, or ends abruptly. Our stair handrail guide covers graspability, height and returns.
- Brackets and attachment: Turns and ends of rails take more force. Loose or missing brackets are common at landings. See our guide to the handrail bracket for typical attachment methods.
- Guards on open sides: Intermediate landings that are open on one or more sides and sit well above the floor below generally need a guard, not just a handrail. The stair railing guide explains the difference.
- Guard and handrail height: Guard heights at landings are often measured differently than handrail heights along the stair. Our stair railing height guide breaks this down.
Older adults benefit most from good rails. The Centers for Disease Control and Prevention suggests putting railings on both sides of stairs and making sure the home has plenty of light as part of making a home safer against falls (CDC). A second handrail and a light switch reachable from each landing are relatively simple upgrades.
Basement Stair Landings
Basement stairs are one of the most common places to find landing problems. Many older homes have basement stairs that open directly into a door at the top, sometimes with the door swinging over the top step. Others turn at a cramped landing beside a foundation wall, end at the bottom against a furnace or water heater, or drop onto a concrete floor with a short last step because the slab was poured after the stairs were built. Finishing a basement often adds flooring, which can change the height of the bottom riser and create a mismatch.
Headroom over basement landings is another frequent issue, especially where ductwork or beams cross over the turn. Our guide to basement stairs covers these older-home quirks and the common fixes.
Fall Risk and Why Landings Matter
Stairs are a frequent setting for household falls, and landings play a part in preventing them by breaking long climbs, giving people a place to steady themselves and providing a safe place to open doors. The CDC reports that more than one out of four older people falls each year and that falling once doubles the chance of falling again. Its list of home hazards that make falls more likely includes broken or uneven steps and throw rugs or clutter that can be tripped over (CDC).
Several of those hazards gather at landings. Rugs and runners placed on a landing can slide. Laundry baskets, shoes and boxes tend to be set down on a landing because it looks like spare floor space. Landings at the top of basement stairs are often dimly lit. Keeping landings clear, securing any rug firmly, and adding lighting are low-cost steps that address the issues the CDC describes.
What a Home Inspector Looks For
The American Society of Home Inspectors Standard of Practice lists steps, stairways and railings among interior items an inspector shall inspect, and it lists attached and adjacent decks, balconies, stoops, steps, porches and their associated railings in the exterior section (ASHI). In practice, notes about landings often include:
- A door that swings over a step with no level landing.
- Landings that are undersized, out of level, springy or visibly sagging.
- Inconsistent riser height at the top or bottom of a flight.
- Handrails that end at a landing or are loose at the turn.
- Open-sided landings without adequate guards.
- Exterior stoops that have settled, cracked or slope toward the house.
- Deck stair landings on soil or unsupported platforms.
A home inspection is a visual review of conditions, not a code compliance check. An inspector may point out conditions that do not appear to meet current standards in an older home, but those may have been acceptable when the house was built. Whether an existing landing must be changed is usually a question for a remodel or permit, not a resale requirement.
Repair and Upgrade Costs
Costs depend heavily on the type of landing, materials, access and local labor rates. The ranges below are broad and hedged.
- Adding or extending a handrail around a landing: often a few hundred dollars for a straightforward wall-mounted rail, more for custom wood or metal work.
- Re-securing or reinforcing a sagging interior landing: may be modest if framing is accessible from below, or considerably more if finishes have to be opened up.
- Mudjacking or leveling a settled concrete stoop: often in the hundreds to low thousands, depending on size and method.
- Replacing a concrete stoop or building a new exterior landing: commonly in the low thousands or higher, especially with footings, railings and permits.
- Reconfiguring a stair to add a landing: a larger project that may involve framing changes, new stringers, finishes and permits, often running into several thousand dollars or more.
Rehanging a door so it swings away from a stair, or adding lighting and a second handrail, can address some landing issues without rebuilding. Getting more than one quote and asking each contractor how the work will be permitted helps compare options.
Landings are one part of a broader stair and structure review. Our guide to the lintel covers a masonry detail inspectors check over doors and windows. For advice on comparing contractors for stair and exterior work, see the structure and exterior section of our hiring guide, and for choosing an inspector more broadly, start with our home inspector hiring guide.
More Questions About Stair Landings
How small can a bottom stair landing be?
Under the International Residential Code, a stair landing must generally be at least as wide as the stairway and at least 36 inches deep in the direction of travel.
That means a 36-inch-wide stair typically needs at least a 36-by-36-inch landing at the bottom. Local codes can differ, and doors that swing over the landing can affect the required size. Check with the local building department before building or remodeling stairs.
When is a landing needed at the top of stairs?
A landing is generally required at the top and bottom of every interior and exterior stairway under the International Residential Code, with some exceptions.
One common exception allows a door at the top of an interior stair to swing away from the stairs without a landing in front of it. Exterior stairs from a door usually need a landing on the outside of the door, though small step-downs are permitted in some cases. Local adoption of the code can change details, so confirm with the building department.
Is a landing required where stairs meet an exterior door?
Yes, an exterior door usually needs a landing on each side, with the outside landing no more than a set distance below the door threshold.
Under the International Residential Code, the exterior landing can typically be up to about 7.75 inches below the threshold when the door does not swing over it. The landing should be at least as wide as the door and at least 36 inches deep. Decks and stoops often serve as the landing.
How big should a landing be for exterior home stairs?
Exterior home stair landings are generally required to be at least as wide as the stairs and at least 36 inches deep, though larger landings of 4 to 5 feet are more comfortable for carrying items and opening doors.
Landings exposed to weather should slope slightly for drainage, use slip-resistant surfaces, and be built on solid footings. Long exterior stairs may need an intermediate landing, since the code limits the height of a single flight to about 12 feet.
References
- Facts About Older Adult Falls — Centers for Disease Control and Prevention
- Preventing Falls and Hip Fractures — Centers for Disease Control and Prevention
- ASHI Standard of Practice for Home Inspections — American Society of Home Inspectors
Frequently asked questions
What is a stair landing?
A landing is a level platform at the top or bottom of a stair, between two flights, or where a stair changes direction. It gives people room to stop, turn, open doors and regain balance.
How big does a landing need to be?
As a general rule, a landing is expected to be at least as wide as the stair and about as deep as the stair is wide in the direction of travel. Exact minimums depend on the locally adopted code, so confirm with the building department.
Do exterior doors need a landing?
Exterior doors generally need a level landing on each side, though many codes include limited exceptions. A door that opens directly onto a step is a common inspection note.
Should a handrail continue around a landing?
Codes may allow a handrail to break at a landing, but a rail that runs continuously around the turn is generally easier and safer to use, especially for older adults and children.
Will a home inspector check stair landings?
Yes. Inspectors typically look at stairways, railings, stoops and deck stairs and may note undersized or sagging landings, loose rails, missing guards and uneven risers.
What is the average size of a staircase landing?
Many residential staircase landings measure about 36 by 36 inches at minimum, with common sizes around 3 by 4 feet or larger. Size depends on stair width, door swings and whether the stairs turn at the landing.
What is a landing in the middle of stairs called?
A landing in the middle of stairs is often called an intermediate landing or a mid-landing. Where the stairs turn 90 degrees, it may be called a quarter-space landing, and where they turn 180 degrees, a half-space landing.
Can a stair landing have winder steps instead?
Winder treads can sometimes replace a flat landing at a turn, but they must meet specific code dimensions for tread depth. Winders are more common in homes than commercial buildings and need careful design to reduce trip risk.
Buying a split-level or a home with steep basement stairs on the Front Range? Get in touch and we can help you find an inspector who looks closely at stairs, rails and landings.