Mudjacking vs Foam Lifting: Costs and When It Works
A sunken sidewalk panel, a patio that tilts toward the back door, or a driveway slab that has dropped an inch below the garage floor is more than a cosmetic problem. Uneven concrete creates trip hazards, and slabs that slope toward the house can send rain and snowmelt straight at the foundation. Tearing out and repouring concrete is expensive and messy, so many homeowners look at lifting the existing slab instead. Mudjacking, also called slabjacking, is the older of the two main lifting methods; polyurethane foam injection is the newer one. This guide explains how each method works, what kinds of concrete can and cannot be lifted, why slabs sink in the first place, especially on Front Range soils, and what homeowners can expect to pay. Cost ranges are general 2026 estimates that vary by contractor, region and job size.
Part of our Structure & Exterior guide — start there for the full picture →
What Is Mudjacking?
Mudjacking is a method of raising settled concrete by pumping a cement-based slurry underneath it. A contractor drills a series of holes through the sunken slab, typically around 1 to 2 inches in diameter. A grout mixture, usually some combination of water, soil or sand, and portland cement, is pumped through those holes under pressure. The slurry fills the voids beneath the slab, and as more material goes in, hydraulic pressure lifts the concrete back toward its original level. When the slab is in position, the holes are patched with cement, and the material underneath cures into a solid base.
In short, mudjacking does not replace concrete. It re-supports and repositions the slab that is already there. When the slab itself is in reasonable condition and the problem is the soil underneath, that can be far cheaper and faster than tearing out and pouring new concrete.
Mudjacking vs Polyurethane Foam Lifting
Polyurethane foam lifting, sometimes called polyjacking or foam jacking, works on the same principle but uses a different material. Instead of a cement slurry, the contractor injects a two-part expanding foam through much smaller holes. The foam expands as it reacts, fills the voids and lifts the slab. Each method has trade-offs.
Cost
Mudjacking is generally the less expensive of the two per square foot. Foam lifting often costs more because the material is more expensive, though the gap varies by market and by how much void space needs to be filled.
Weight
Cement slurry is heavy. Adding a large volume of it under a slab places more weight on soils that may already be weak, which can contribute to future settling. Polyurethane foam is much lighter, which some contractors see as an advantage on soft or poorly compacted soils.
Hole size and appearance
Mudjacking holes are larger, commonly 1 to 2 inches, and the patches tend to remain visible as gray circles. Foam injection holes are often around 5/8 inch, so the patches are smaller and less noticeable.
Cure time
Mudjacked slabs usually need a day or more before vehicles drive on them, depending on the mix and the weather. Polyurethane foam typically cures quickly, and many contractors say slabs can be used within hours.
Longevity and water resistance
Both methods can last for years when the underlying cause of settling is addressed. Foam does not wash out easily and is not affected by moisture the way some slurry mixes can be. Slurry can erode over time if water continues to run under the slab. Neither method fixes poor drainage on its own, so longevity depends heavily on what happens to water around the slab after the repair.
Precision
Foam can be injected in small increments, which gives fine control over the final level. Mudjacking can also be precise in skilled hands, but the heavier slurry and larger holes give a contractor less room for small adjustments.
For many straightforward jobs, such as a sunken sidewalk panel or a patio slab on reasonably stable soil, mudjacking remains a cost-effective choice. Foam lifting may be worth the premium where weight, appearance or quick return to service matter most.
What Can and Cannot Be Lifted
Slab lifting works best on flat concrete that has sunk as a single piece and is still structurally sound.
Good candidates often include:
- Sidewalk and walkway panels that have dropped and created a lip.
- Patios that have settled or tilted toward the house.
- Driveway slabs, particularly where a section has dropped at the garage apron or the street.
- Garage floor slabs that have settled near the door or at a joint.
- Concrete steps and stoops that have pulled away from the house, if the steps are a solid unit.
- Pool decks and porch slabs in some cases.
Poor candidates often include:
- Slabs broken into many pieces or crumbling at the surface. Lifting a badly cracked slab can widen the cracks or leave uneven pieces.
- Concrete that has heaved upward rather than sunk. Lifting cannot lower a slab.
- Thin, deteriorated or very old concrete with heavy spalling.
- Structural foundations and footings. Settlement of the house itself calls for a structural evaluation and usually different methods, such as piers. The guide to foundation settlement explains warning signs and how engineers approach it.
Driveways with scattered surface cracking but no major drop are often better served by crack repair and sealing than by lifting. The guide to driveway cracks covers the difference between cosmetic and structural cracking, and the guide to concrete sealer explains how sealing can protect a slab once it is level.
Why Concrete Slabs Sink
Lifting a slab without understanding why it sank often means paying for the same repair again. The most common causes include:
- Washout. Water running under a slab carries fine soil away and leaves voids. Downspouts that discharge onto or beside a sidewalk or patio are frequent culprits.
- Poor compaction. Soil backfilled around a new house is often loose. As it settles over the first several years, slabs poured on top of it sink, especially patios and walkways near the foundation.
- Expansive soils. Much of the Colorado Front Range, including parts of Douglas, Arapahoe, Jefferson and El Paso counties, has clay soils that swell when wet and shrink when dry. Repeated cycles can lift, drop and tilt flatwork.
- Freeze-thaw cycles. Water that collects under or beside a slab can freeze and expand, then thaw and leave voids. Colorado’s frequent winter freeze-thaw swings make this a recurring stress.
- Plumbing leaks. A leaking irrigation line or underground pipe can saturate and wash out the soil beneath a slab.
- Tree roots. Roots can push slabs up as they grow and leave voids when they die and decay.
Drainage is the cause homeowners can most often control. Extending downspouts so they discharge well away from flatwork, as described in the guide to a downspout extension, keeps roof water from undermining sidewalks and patios. EPA guidance on redirecting downspouts notes that the location of discharged water should be chosen to avoid property damage and unsafe conditions. Broader grading problems are covered in the guide to yard drainage.
Trip Hazards and Slopes Toward the House
Two problems usually push homeowners to act on sunken concrete.
The first is safety. A sidewalk panel that has dropped below its neighbor creates a lip that is easy to catch with a toe, particularly at night or for older visitors. Many cities set a height threshold for public sidewalk trip hazards that triggers repair, and homeowners are often responsible for sidewalk panels in front of their property. Local rules vary, so check with the city or county.
The second is water. A patio, stoop or walkway that settles toward the house turns into a channel that drains rain and snowmelt toward the foundation. The EPA’s moisture guidance recommends making sure the ground slopes away from the building foundation so water does not enter or collect around it. When flatwork tilts the wrong way, it can contribute to damp basements, efflorescence and crack activity. If water has already found its way inside, the guide to basement floor cracks explains what different crack patterns may indicate. Lifting a slab to restore a slope away from the house is one of the more practical uses of mudjacking.
Lift or Replace? A Quick Decision Guide
Not every sunken slab should be lifted. A few practical questions help sort out which repair makes sense:
- Is the slab in one piece? A slab with one or two clean cracks can often be lifted and the cracks sealed. A slab broken into many small pieces usually cannot be lifted evenly.
- How far has it dropped? Small drops of an inch or two are routine lifting jobs. Larger drops are still possible, but large voids take more material and may point to an ongoing soil or water problem worth investigating first.
- What is the surface condition? Heavy spalling, scaling from deicing salts or crumbling edges suggest the concrete is near the end of its life regardless of level.
- Is the problem still active? A slab that has sunk again after a previous lift, or one next to a leaking irrigation line, needs the cause corrected first.
- What will the finished result look like? Lifted slabs keep their original color and texture, plus patch marks. Replacement gives a uniform new surface but may not match adjacent concrete.
In practice, many homeowners lift the sound slabs and replace only the few that are too damaged, which keeps costs down while fixing the worst trip hazards and drainage problems.
Garage floors and steps
Garage slabs deserve a closer look before lifting. Settlement at the front edge near the overhead door is common and often lifts well. Settlement in the middle of the floor, or cracks that continue into the foundation wall, may indicate a broader soil issue. Concrete steps are lifted as a block when they are solid; steps that have separated from their landing or have hollow cores may need to be rebuilt.
Preventing Future Settlement
Once slabs are level, a few habits help keep them that way:
- Keep downspouts discharging several feet beyond walkways and patios, not onto them.
- Seal joints between slabs and along the foundation with a flexible sealant, and renew it as it ages.
- Check irrigation heads and lines near flatwork each spring for leaks or overspray.
- Fill and compact low spots in soil beside slab edges so water does not pool and soak underneath.
Mudjacking Costs
Pricing depends on the size and thickness of the slab, how far it has sunk, how much void space must be filled, access for equipment and local labor rates. Many contractors also have a minimum job charge. These ranges are general estimates, not quotes:
- Mudjacking: commonly about $3 to $7 per square foot, with many small jobs falling somewhere around $500 to $1,500.
- Polyurethane foam lifting: often roughly $5 to $15 per square foot, depending on the amount of foam required.
- Minimum charges: frequently several hundred dollars even for a single sidewalk panel.
- Concrete replacement for comparison: tearing out and repouring flatwork commonly costs considerably more per square foot than lifting, plus demolition and disposal.
Quotes should state the number of slabs, the target lift, the material used, whether joints and cracks will be sealed afterward, and whether there is any warranty. A low quote that does not mention sealing joints or addressing drainage may lead to the same slab sinking again.
What to Expect During the Job
A typical mudjacking visit is short. Many residential jobs take a few hours. The contractor marks the slab, drills the injection holes, pumps the slurry while monitoring the slab with a level or string line, then patches the holes. Joints between slabs and along the house are often sealed with a flexible sealant to slow water entry.
Drilling concrete creates dust. OSHA notes that drilling into concrete is one of the activities that can expose workers to respirable crystalline silica dust, so reputable contractors use dust controls such as water or vacuum-equipped drills. Homeowners should keep children and pets away from the work area and close nearby windows while drilling is underway.
After the job, expect visible patch circles and the need to avoid driving on lifted driveway sections until the contractor says the material has cured. Watch the area through the next few heavy rains to confirm water now drains away as intended.
DIY or Hire a Contractor?
Mudjacking is not a practical DIY project. It requires a drill capable of boring through slabs, a pump that can push heavy slurry under pressure, and the experience to lift a slab evenly without cracking it. Homeowners can handle the related tasks, such as extending downspouts, regrading soil beside a patio, and sealing joints, but the lifting itself is best left to an experienced flatwork or slab-lifting contractor.
When collecting quotes, it helps to ask:
- Do you recommend slurry or foam for this job, and why?
- What do you think caused the settlement, and does the quote address it?
- Will you seal joints and cracks after the lift?
- How long before the slab can be walked or driven on?
- Is there a warranty, and what does it cover if the slab settles again?
- Are you licensed and insured where required locally?
How Sunken Concrete Shows Up in a Home Inspection
Exterior flatwork is part of a standard home inspection. Under the ASHI Standard of Practice, inspectors look at adjacent and entryway walkways, patios and driveways, along with grading and surface drainage likely to adversely affect the building. Inspectors commonly note settled slabs, trip hazards, negative slope toward the house and gaps where stoops have pulled away. They do not typically determine why the soil settled or estimate repair costs. If an inspector flags settlement near the house itself, a structural engineer’s opinion may be worthwhile before closing. The guide to hiring a home inspector covers how to ask about the scope of exterior evaluation, and specialty inspections explains when follow-up evaluations make sense.
For sellers, lifting a tilted patio or a sunken walkway before listing can remove an easy negotiating point, especially when the slab slopes toward the foundation and the report would otherwise flag a drainage concern.
More Questions About Mudjacking
Can mudjacking be done in winter?
Mudjacking can sometimes be done in winter, but most contractors avoid it when the ground is frozen or temperatures stay below freezing, because the cement slurry cures poorly and frozen soil can heave and settle as it thaws.
Lifting a slab on frozen ground may look level at first and then drop again in spring. Many contractors schedule mudjacking from spring through fall. Polyurethane foam lifting is less sensitive to cold, so it is sometimes used during mild winter spells. Trip hazards that cannot wait can be marked or ramped temporarily until conditions improve.
How soon can you drive on a mudjacked driveway?
Most contractors advise waiting about 24 to 48 hours before driving on a mudjacked driveway, while walking is usually fine sooner, often within a few hours.
The slurry pumped under the slab needs time to set and support heavy loads. Cool or wet weather can lengthen the wait. Heavy vehicles such as moving trucks or delivery vans should be kept off longer. The contractor’s specific advice should take priority, since it depends on the slurry mix and the size of the lifted area. The patched injection holes also need time to cure.
Can mudjacking fix a sinking pool deck?
Mudjacking can often raise a sinking concrete pool deck, but lifting near pools must be done carefully to avoid damaging pool walls, coping, and nearby plumbing lines.
Pool decks sink when water leaks, splash-out, or poor compaction wash out the soil beneath them. Many contractors prefer polyurethane foam around pools because it is lighter, uses smaller holes, and is less likely to wash out. Fixing the water source, such as a leaking pipe or poor drainage, is essential. After lifting, caulking the joint between deck and coping helps keep water out.
Does mudjacking work on a basement floor?
Mudjacking can lift a settled basement floor slab in some cases, but interior slabs are more complicated because of plumbing lines, drains, and the risk of moisture issues beneath the floor.
Basement slabs usually sit on gravel and are not structural, so settlement often relates to soil compaction or water movement. Before lifting, the cause of settlement should be identified, especially if walls are cracking or bowing, which can signal foundation problems. Many contractors favor polyurethane foam indoors because it weighs less and creates less mess. A structural engineer can advise on significant cracking.
Will mudjacking crack the concrete slab?
Mudjacking can occasionally crack a concrete slab during lifting, especially if the slab is thin, already cracked, or lifted unevenly, but experienced contractors lift gradually to reduce that risk.
Existing cracks may widen or new hairline cracks may appear as pressure builds under the slab. Severely broken or deteriorated slabs may not be good candidates, and replacement may be the better choice. Asking the contractor how they handle cracks, what warranty they offer, and whether they will seal cracks afterward helps set expectations before work begins.
References
- ASHI Standard of Practice for Home Inspections — American Society of Home Inspectors
- A Brief Guide to Mold, Moisture and Your Home: Sloping Ground Away From the Foundation — U.S. Environmental Protection Agency
- Soak Up the Rain: Disconnect and Redirect Downspouts — U.S. Environmental Protection Agency
- Silica, Crystalline: Hazard Overview — Occupational Safety and Health Administration
Frequently asked questions
How long does mudjacking last?
Mudjacking can last many years when the cause of settling, such as poor drainage or washout, is corrected. If water keeps running under the slab, the slurry and soil can erode and the slab may sink again.
Is mudjacking cheaper than foam lifting?
Mudjacking is generally less expensive per square foot. Polyurethane foam usually costs more but uses smaller holes, weighs less and cures faster. The better choice depends on the soil, the slab and the budget.
Can mudjacking fix a cracked driveway?
Mudjacking can lift a driveway slab that has sunk as a single piece. Slabs broken into many pieces or crumbling at the surface are usually poor candidates and may need partial replacement instead.
Can mudjacking be used on a house foundation?
Mudjacking is meant for flatwork such as sidewalks, patios, driveways and garage floors. Settlement of a house foundation needs a structural evaluation and typically different repair methods, such as piers.
How much does mudjacking cost?
Mudjacking commonly costs about $3 to $7 per square foot, and many small jobs fall around $500 to $1,500. Contractors often have minimum charges, and prices vary by region and job size.
What is the mudjacking slurry made of?
Mudjacking slurry is typically a mix of water, soil or sand, and Portland cement, sometimes with additives like lime or fly ash. The exact mix varies by contractor. It is heavier than polyurethane foam, which is one reason mudjacking may cause more settlement over time.
Does mudjacking fill voids under a slab?
Yes, mudjacking fills voids under a slab, which is part of how it restores support. The slurry flows into gaps caused by erosion or settlement, then lifts the slab as pressure builds. Filling voids also helps prevent future sinking if drainage problems are fixed.
Can mudjacking holes be hidden?
Mudjacking holes, usually about one to two inches wide, are patched with cement after lifting and remain somewhat visible because the patch rarely matches older concrete exactly. Careful contractors try to place holes in less noticeable spots. Foam lifting uses smaller holes.
Noticed a patio tilting toward the house or a sunken walkway at a home you are about to buy? Reach out to our team and we can connect you with a vetted Front Range inspector who can flag drainage and settlement concerns before closing.